| Age | Commit message (Collapse) | Author |
|---|
|
The kernel has very specific rules correlating file type with comment
type, and also SPDX identifiers can't be merged with other comments.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
This is the worst commit in the whole repo, making the code much less
readable, but so it goes with upstream maintainers.
We are now woefully wrapped at 80 columns.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Rather than abusing the handshake lock, we're much better off just using
a boring atomic64 for this. It's simpler and performs better.
Also, while we're at it, we set the handshake stamp both before and
after the calculations, in case the calculations block for a really long
time waiting for the RNG to initialize. Otherwise it's possible that
when the RNG finally initializes, two handshakes are sent back to back,
which isn't sensible.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Completely rework peer removal to ensure peers don't jump between
contexts and create races.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
After we atomic_set, the peer is allowed to be freed, which means if we
want to continue to reference it, we need to bump the reference count.
This was introduced a few commits ago by b713ab0e when implementing some
simplification suggestions.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Use RCU reference counts only when we must, and otherwise use a more
reasonably named function.
Reported-by: Jann Horn <jann@thejh.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Suggested-by: Jason A. Donenfeld <Jason@zx2c4.com>
[Jason: fixed up the flushing of the rx_queue in peer_remove]
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Generally if we're inaccurate by a few nanoseconds, it doesn't matter.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Since this is a network protocol, expirations need to be accounted for,
even across system suspend. On real systems, this isn't a problem, since
we're clearing all keys before suspend. But on Android, where we don't
do that, this is something of a problem. So, we switch to using boottime
instead of jiffies.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
It's good to have SPDX identifiers in all files as the Linux kernel
developers are working to add these identifiers to all files.
Update all files with the correct SPDX license identifier based on the license
text of the project or based on the license in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of the
full boiler plate text.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modified-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
This gets us nanoseconds instead of microseconds, which is better, and
we can do this pretty much without freaking out existing userspace,
which doesn't actually make use of the nano/micro seconds field:
zx2c4@thinkpad ~ $ cat a.c
void main()
{
puts(sizeof(struct timeval) == sizeof(struct timespec) ? "success" : "failure");
}
zx2c4@thinkpad ~ $ gcc a.c -m64 && ./a.out
success
zx2c4@thinkpad ~ $ gcc a.c -m32 && ./a.out
success
This doesn't solve y2038 problem, but timespec64 isn't yet a thing in
userspace.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
This is faster, since it means adding a new peer is O(1) instead of
O(n). It's also safe to do because we're holding the device_update_lock
on both the ++ and the --.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Since the peer list is protected by the device_update_lock, and since
items are removed from the peer list before putting their final
reference, we don't actually need to take a reference when iterating.
This allows us to simplify the macro considerably.
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Suggested-by: Sultan Alsawaf <sultanxda@gmail.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
This removes our dependency on padata and moves to a different mode of
multiprocessing that is more efficient.
This began as Samuel Holland's GSoC project and was gradually
reworked/redesigned/rebased into this present commit, which is a
combination of his initial contribution and my subsequent rewriting and
redesigning.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
We store the destination IP of incoming packets as the source IP of
outgoing packets. When we send outgoing packets, we then ask the routing
table for which interface to use and which source address, given our
inputs of the destination address and a suggested source address. This
all is good and fine, since it means we'll successfully reply using the
correct source address, correlating with the destination address for
incoming packets. However, what happens when default routes change? Or
when interface IP addresses change?
Prior to this commit, after getting the response from the routing table
of the source address, destination address, and interface, we would then
make sure that the source address actually belonged to the outbound
interface. If it didn't, we'd reset our source address to zero and
re-ask the routing table, in which case the routing table would then
give us the default IP address for sending that packet. This worked
mostly fine for most purposes, but there was a problem: what if
WireGuard legitimately accepted an inbound packet on a default interface
using an IP of another interface? In this case, falling back to asking
for the default source IP was not a good strategy, since it'd nearly
always mean we'd fail to reply using the right source.
So, this commit changes the algorithm slightly. Rather than falling back
to using the default IP if the preferred source IP doesn't belong to the
outbound interface, we have two checks: we make sure that the source IP
address belongs to _some_ interface on the system, no matter which one
(so long as it's within the network namespace), and we check whether or
not the interface of an incoming packet matches the returned interface
for the outbound traffic. If both these conditions are true, then we
proceed with using this source IP address. If not, we fall back to the
default IP address.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Suggested-by: Mathias Hall-Andersen <mathias@hall-andersen.dk>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
If it's time to rekey, and the responder sends a message, the initator
will begin the rekeying when sending his response message. In the worst
case, this response message will actually just be the keepalive. This
generally works well, with the one edge case of the message arriving
less than 10 seconds before key expiration, in which the keepalive is
not sufficient. In this case, we simply rehandshake immediately.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
With the prior behavior, when sending a packet, we checked to see if it
was about time to start a new handshake, and if we were past a certain
time, we started it. For the responder, we made that time a bit further
in the future than for the initiator, to prevent the thundering herd
problem of them both starting at the same time. However, this was
flawed.
If both parties stopped communicating after 2.2 minutes, and then one
party decided to initiate a TCP connection before the 3 minute mark, the
currently open session would be used. However, because it was after the
2.2 minute mark, both peers would try to initiate a handshake upon
sending their first packet. The errant flow was as follows:
1. Peer A sends SYN.
2. Peer A sees that his key is getting old and initiates new handshake.
3. Peer B receives SYN and sends ACK.
4. Peer B sees that his key is getting old and initiates new handshake.
Since these events happened after the 2.2 minute mark, there's no delay
between handshake initiations, and problems begin. The new behavior is
changed to:
1. Peer A sends SYN.
2. Peer A sees that his key is getting old and initiates new handshake.
3. Peer B receives SYN and sends ACK.
4. Peer B sees that his key is getting old and schedules a delayed
handshake for 12.5 seconds in the future.
5. Peer B receives handshake initiation and cancels scheduled handshake.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
The C standard states:
A declaration of a parameter as ``array of type'' shall be adjusted to ``qualified pointer to
type'', where the type qualifiers (if any) are those specified within the [ and ] of the
array type derivation. If the keyword static also appears within the [ and ] of the
array type derivation, then for each call to the function, the value of the corresponding
actual argument shall provide access to the first element of an array with at least as many
elements as specified by the size expression.
By changing void func(int array[4]) to void func(int array[static 4]),
we automatically get the compiler checking argument sizes for us, which
is quite nice.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
