blob: 6ec968fd80797fdded14300fdc6a8352c09a5434 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
|
##
## tinyproxy.conf -- tinyproxy daemon configuration file
##
#
# Name of the user the tinyproxy daemon should switch to after the port
# has been bound.
#
User nobody
Group nogroup
#
# Port to listen on.
#
Port 8888
#
# If you have multiple interfaces this allows you to bind to only one. If
# this is commented out, tinyproxy will bind to all interfaces present.
#
#Listen 192.168.0.1
#
# Timeout: The number of seconds of inactivity a connection is allowed to
# have before it closed by tinyproxy.
#
Timeout 600
#
# Where to log the information. Either LogFile or Syslog should be set,
# but not both.
#
Logfile "/var/log/tinyproxy.log"
# Syslog On
#
# PidFile: Write the PID of the main tinyproxy thread to this file so it
# can be used for signalling purposes.
#
PidFile "/var/run/tinyproxy.pid"
#
# Include the X-Tinyproxy header, which has the client's IP address when
# connecting to the sites listed.
#
#XTinyproxy mydomain.com
#
# Turns tinyproxy into a TCP tunnel which connects the local computer on
# 'Port' to the remote computer's port. The form is remote_machine port
#
#Tunnel some.remote.computer:port
#
# This is the absolute highest number of threads which will be created. In
# other words, only MaxClients number of clients can be connected at the
# same time.
#
MaxClients 100
#
# These settings set the upper and lower limit for the number of
# spare servers which should be available. If the number of spare servers
# falls below MinSpareServers then new ones will be created. If the number
# of servers exceeds MaxSpareServers then the extras will be killed off.
#
MinSpareServers 5
MaxSpareServers 20
#
# Number of servers to start initially.
#
StartServers 10
#
# MaxRequestsPerChild is the number of connections a thread will handle
# before it is killed. In practice this should be set to 0, which disables
# thread reaping. If you do notice problems with memory leakage, then set
# this to something like 10000
#
MaxRequestsPerChild 0
#
# The following is the authorization controls. If there are any access
# control keywords then the default action is to DENY. Otherwise, the
# default action is ALLOW.
#
# Also the order of the controls are important. The incoming connections
# are tested against the controls based on order.
#
Allow 127.0.0.1
Allow 192.168.1.0/25
#
# The location of the filter file.
#
#Filter "/etc/tinyproxy/filter"
#
# If an Anonymous keyword is present, then anonymous proxying is enabled.
# The headers listed are allowed through, while all others are denied. If
# no Anonymous keyword is present, then all header are allowed through.
#
#Anonymous Host
#Anonymous Authorization
|
