| Age | Commit message (Collapse) | Author |
|---|
|
Config support to set the MLD host version on device level; possible values are :
1 : MLDv1
2 : MLDv2
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Cleaned up and simplified.
Signed-off-by: Steven Barth <steven@midlink.org>
|
|
Config support to set the IGMP host version on device level; possible values are :
1 : IGMPv1
2 : IGMPv2
3 : IGMPv3
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Cleand up and simplified
Signed-off-by: Steven Barth <steven@midlink.org>
|
|
Reverse path filtering config support; possible values are:
0: no source validation
1|strict: strict mode as packet will be dropped if the
incoming interface is not the best reverse path
2|loose: loose mode as packet will be dropped if the
source address is not reachable via any interface
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
|
|
When a device with the same name is deleted and created again in the kernel
the ifindex changes.
A race condition will occur when netlink event messages linked to the old device
are processed and will thus overwrite the correct ifindex of the new device.
Further make sure a valid ifindex is in place for both external and internal
devices when setting the state to enabled.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
|
|
Adds support for gre, gretap, grev6 and grev6tap tunnels
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
|
|
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
|
|
Do not treat RT_TABLE_MAIN as RT_TABLE_UNSPEC in system_resolve_rt_table() in
order to allow ip rules with lookup main to work as expected.
Provide a new function system_is_default_rt_table() to allow calling code to
specifically test for RT_TABLE_MAIN, this is going to be needed for the
backwards compatible handling of the table attribute in route objects.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
|
|
Patch adds route type support in netifd by means of the route parameter type.
By default the route type was unicast; the parameter adss support for local/broadcast/multicast/unicast routes which will be put into the appropriate routing table.
If route type parameter is unset the route type will be unicast as before.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
|
|
At moment netifd supports just 802.1q vlan, you can configure them using a concise but "hacky"
syntax using an interface config section, with this patch netifd acquire the capability
of configuring 802.1ad and 802.1q vlan using config device sections, so you can define a vlan device
plus interface with something like this:
config device 'test'
option type '8021ad'
option name 'test'
option ifname 'eth0'
option vid '1000'
config interface 'testif'
option ifname 'test'
option proto 'none'
option auto '1'
old syntax for 802.1q keeps working so no retrocompatibility problems,
to keep retrocompatibility means also that user must not use name/ifname like eth0.2
for devices declared with the new style because this would trigger the "old style"
when interface config section is parsed
Signed-off-by: Gioacchino Mazzurco <gmazzurco89@gmail.com>
|
|
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
|
|
Reapply bridge mtu setting as adding a bridge member will override the bridge mtu in the kernel
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
|
|
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
|
|
|
|
|
|
|
|
Signed-off-by: Steven Barth <steven@midlink.org>
|
|
|
|
devices
|
|
|
|
|
|
|
|
sit supported)
|
|
|
|
|
|
|
|
|
|
|
|
detailed device information
|
|
|
|
|
|
|
|
to 1
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
system_{add,del}_addr
|
|
|
|
|
|
|
