From 30e79c0ff3c32690aaca24b8d308bda041779767 Mon Sep 17 00:00:00 2001 From: Manuel Munz Date: Sun, 8 May 2011 22:56:29 +0000 Subject: luci-olsr: Add options for SmartGateway. --- po/ca/olsr.po | 54 +++++++++++++++++++++++++++++++++++++++++++++++++----- 1 file changed, 49 insertions(+), 5 deletions(-) (limited to 'po/ca/olsr.po') diff --git a/po/ca/olsr.po b/po/ca/olsr.po index 9a4b7a84a..d09eeb9b3 100644 --- a/po/ca/olsr.po +++ b/po/ca/olsr.po @@ -26,6 +26,15 @@ msgstr "Anuncis de xarxa de màquines actives" msgid "Advanced Settings" msgstr "" +msgid "Allow gateways with NAT" +msgstr "" + +msgid "Allow the selection of an outgoing ipv4 gateway with NAT" +msgstr "" + +msgid "Announce uplink" +msgstr "" + msgid "Announced network" msgstr "Xarxa anunciada" @@ -53,6 +62,11 @@ msgstr "" msgid "Enable" msgstr "" +msgid "" +"Enable SmartGateway. If it is disabled, then all other SmartGateway " +"parameters are ignored. Default is \"no\"." +msgstr "" + msgid "Enable this interface." msgstr "" @@ -167,6 +181,9 @@ msgid "" "of a not-linklocal interface IP." msgstr "" +msgid "IPv6-Prefix of the uplink" +msgstr "" + msgid "" "If the route to the current gateway is to be changed, the ETX value of this " "gateway is multiplied with this value before it is compared to the new one. " @@ -175,6 +192,10 @@ msgid "" "with the etx_ffeth metric!
Defaults to \"1.0\"." msgstr "" +msgid "" +"If this Node uses NAT for connections to the internet. Default is \"yes\"." +msgstr "" + msgid "Interface" msgstr "" @@ -398,9 +419,6 @@ msgid "" "really slow. In this case disable it here." msgstr "" -msgid "Routen" -msgstr "" - msgid "Routes" msgstr "" @@ -425,6 +443,14 @@ msgstr "" msgid "Source address" msgstr "" +msgid "" +"Specifies the speed of the uplink in kilobits/s. First parameter is " +"upstream, second parameter is downstream. Default is \"128 1024\"." +msgstr "" + +msgid "Speed of the uplink" +msgstr "" + msgid "State" msgstr "" @@ -470,10 +496,14 @@ msgid "" "It can have a value between 1 and 65535." msgstr "" -msgid "Timing and Validity" +msgid "" +"This can be used to signal the external IPv6 prefix of the uplink to the " +"clients. This might allow a client to change it's local IPv6 address to use " +"the IPv6 gateway without any kind of address translation. The maximum prefix " +"length is 64 bits. Default is \"::/0\" (no prefix)." msgstr "" -msgid "Topologie" +msgid "Timing and Validity" msgstr "" msgid "Topology" @@ -490,6 +520,9 @@ msgstr "No s'ha pogut connectar al dimoni OLSR" msgid "Uplink" msgstr "" +msgid "Uplink uses NAT" +msgstr "" + msgid "Use hysteresis" msgstr "Utilitza histèresi" @@ -499,6 +532,11 @@ msgstr "" msgid "WLAN" msgstr "" +msgid "" +"Warning: kmod-ipip is not installed. Without kmod-ipip SmartGateway will not " +"work, please install it." +msgstr "" + msgid "Weight" msgstr "" @@ -512,5 +550,11 @@ msgid "" "instead." msgstr "" +msgid "" +"Which kind of uplink is exported to the other mesh nodes. An uplink is " +"detected by looking for a local HNA of 0.0.0.0/0, ::ffff:0:0/96 or 2000::/3. " +"Default setting is \"both\"." +msgstr "" + msgid "Willingness" msgstr "Voluntat" -- cgit v1.2.3