po: resync with source code

1 files changed, 88 insertions, 6 deletions

diff --git a/po/zh_CN/olsr.po b/po/zh_CN/olsr.po
index f8c621b9a6..2f3cb8caf1 100644
--- a/po/zh_CN/olsr.po
+++ b/po/zh_CN/olsr.po
@@ -35,17 +35,28 @@ msgstr "广告上行"
 msgid "Announced network"
 msgstr "广告网络"
 
+msgid "Bad (ETX > 10)"
+msgstr ""
+
+msgid "Bad (SNR < 5)"
+msgstr ""
+
 msgid "Both values must use the dotted decimal notation."
 msgstr "两个值必须使用点分十进制表示法。"
 
 msgid "Broadcast address"
 msgstr "广播地址"
 
+msgid "Can only be a valid IPv4 or IPv6 address or 'default'"
+msgstr ""
+
 msgid "Configuration"
 msgstr "配置"
 
-msgid "Device"
-msgstr "设备"
+msgid ""
+"Could not get any data. Make sure the jsoninfo plugin is installed and "
+"allows connections from localhost."
+msgstr ""
 
 msgid "Display"
 msgstr "显示"
@@ -65,7 +76,8 @@ msgstr "允许"
 msgid ""
 "Enable SmartGateway. If it is disabled, then all other SmartGateway "
 "parameters are ignored. Default is \"no\"."
-msgstr "启用SmartGateway。如果禁用，则SmartGateway其他所有参数将忽略。缺省值：“禁用”"
+msgstr ""
+"启用SmartGateway。如果禁用，则SmartGateway其他所有参数将忽略。缺省值：“禁用”"
 
 msgid "Enable this interface."
 msgstr "启用这个端口"
@@ -100,6 +112,15 @@ msgstr "通用设置"
 msgid "General settings"
 msgstr "通用设置"
 
+msgid "Good (2 < ETX < 4)"
+msgstr ""
+
+msgid "Good (30 > SNR > 20)"
+msgstr ""
+
+msgid "Green"
+msgstr ""
+
 msgid "HNA"
 msgstr "HNA"
 
@@ -121,6 +142,12 @@ msgstr "Hello间隙"
 msgid "Hello validity time"
 msgstr "Hello有效时长"
 
+msgid "Hide IPv4"
+msgstr ""
+
+msgid "Hide IPv6"
+msgstr ""
+
 msgid "Hna4"
 msgstr "Hna4"
 
@@ -234,6 +261,14 @@ msgid ""
 "Default is \"2.5\"."
 msgstr ""
 
+msgid "Invalid Value for LQMult-Value. Must be between 0.01 and 1.0."
+msgstr ""
+
+msgid ""
+"Invalid Value for LQMult-Value. You must use a decimal number between 0.01 "
+"and 1.0 here."
+msgstr ""
+
 msgid "Known OLSR routes"
 msgstr ""
 
@@ -252,6 +287,11 @@ msgstr ""
 msgid "LQ level"
 msgstr ""
 
+msgid ""
+"LQMult requires two values (IP address or 'default' and multiplicator) "
+"seperated by space."
+msgstr ""
+
 msgid "Last hop"
 msgstr ""
 
@@ -313,8 +353,8 @@ msgid "Main IP"
 msgstr ""
 
 msgid ""
-"Make sure that OLSRd is running, the \"txtinfo\" plugin is loaded, "
-"configured on port 2006 and accepts connections from \"127.0.0.1\"."
+"Make sure that OLSRd is running, the \"jsoninfo\" plugin is loaded, "
+"configured on port 9090 and accepts connections from \"127.0.0.1\"."
 msgstr ""
 
 msgid "Metric"
@@ -325,7 +365,7 @@ msgstr ""
 
 msgid ""
 "Multiply routes with the factor given here. Allowed values are between 0.01 "
-"and 1. It is only used when LQ-Level is greater than 0. Examples:<br /"
+"and 1.0. It is only used when LQ-Level is greater than 0. Examples:<br /"
 ">reduce LQ to 192.168.0.1 by half: 192.168.0.1 0.5<br />reduce LQ to all "
 "nodes on this interface by 20%: default 0.8"
 msgstr ""
@@ -387,6 +427,9 @@ msgstr ""
 msgid "OLSR node"
 msgstr ""
 
+msgid "Orange"
+msgstr ""
+
 msgid "Overview"
 msgstr ""
 
@@ -429,6 +472,9 @@ msgstr ""
 msgid "Prefix"
 msgstr ""
 
+msgid "Red"
+msgstr ""
+
 msgid "Resolve"
 msgstr ""
 
@@ -450,6 +496,15 @@ msgid ""
 "IP of the first interface."
 msgstr ""
 
+msgid "Show IPv4"
+msgstr ""
+
+msgid "Show IPv6"
+msgstr ""
+
+msgid "Signal Noise Ratio in dB"
+msgstr ""
+
 msgid "SmartGW"
 msgstr ""
 
@@ -476,6 +531,12 @@ msgstr ""
 msgid "Status"
 msgstr ""
 
+msgid "Still usable (20 > SNR > 5)"
+msgstr ""
+
+msgid "Still usable (4 < ETX < 10)"
+msgstr ""
+
 msgid "Success rate of packages received from the neighbour"
 msgstr ""
 
@@ -545,9 +606,18 @@ msgstr ""
 msgid "Use hysteresis"
 msgstr ""
 
+msgid "Validity Time"
+msgstr ""
+
 msgid "Version"
 msgstr ""
 
+msgid "Very good (ETX < 2)"
+msgstr ""
+
+msgid "Very good (SNR > 30)"
+msgstr ""
+
 msgid "WLAN"
 msgstr ""
 
@@ -577,3 +647,15 @@ msgstr ""
 
 msgid "Willingness"
 msgstr ""
+
+msgid "Yellow"
+msgstr ""
+
+msgid "no"
+msgstr ""
+
+msgid "yes"
+msgstr ""
+
+#~ msgid "Device"
+#~ msgstr "设备"