summaryrefslogtreecommitdiffhomepage
path: root/test/syscalls
AgeCommit message (Collapse)Author
2020-09-27Clean up kcov.Dean Deng
Previously, we did not check the kcov mode when performing task work. As a result, disabling kcov did not do anything. Also avoid expensive atomic RMW when consuming coverage data. We don't need the swap if the value is already zero (which is most of the time), and it is ok if there are slight inconsistencies due to a race between coverage data generation (incrementing the value) and consumption (reading a nonzero value and writing zero). PiperOrigin-RevId: 334049207
2020-09-24test/syscall/mknod: Don't use a hard-coded file nameAndrei Vagin
PiperOrigin-RevId: 333461380
2020-09-23Clean up inotify tests.Dean Deng
Mostly simplifies SKIP_IF statements and adds some more documentation. Also, mknod is now supported by gofer fs, so remove SKIP_IFs related to this. PiperOrigin-RevId: 333449932
2020-09-21Receive ACK when deleting address in syscall testsGhanan Gowripalan
PiperOrigin-RevId: 332961666
2020-09-21Fix socket_ipv4_udp_unbound_test_native in opensource.Zach Koopmans
Calls to recv sometimes fail with EAGAIN, so call select beforehand. PiperOrigin-RevId: 332943156
2020-09-21Fix proc_net_test_native for native tests.Zach Koopmans
"DefaultValueEqZero" is only valid if the test is in a sandbox. Our CI VMs often have "/proc/sys/net/ipv4/ip_forward" set to 1. PiperOrigin-RevId: 332910859
2020-09-21Add ftruncate test for writeable fd but no write permissions.Dean Deng
PiperOrigin-RevId: 332907453
2020-09-21Fix flakes in UdpSocketTestZach Koopmans
`recv` calls with MSG_DONTWAIT can fail with EAGAIN randomly in tests. Fix this by calling `select` on sockets with a timeout prior to attempting a `recv`. PiperOrigin-RevId: 332873735
2020-09-20Merge pull request #3651 from ianlewis:ip-forwardinggVisor bot
PiperOrigin-RevId: 332760843
2020-09-18Disable vdso_clock_gettime on KVM.Jamie Liu
Unfortunately, I think TSC misalignment means that we can't really expect any consistent correspondence between a TSC-based VDSO and the sentry's view of time on the KVM platform. PiperOrigin-RevId: 332576147
2020-09-18Deflake stat_test with save/restore enabled.Nicolas Lacasse
PiperOrigin-RevId: 332546659
2020-09-18Implement fsimpl/overlay.filesystem.RenameAt.Jamie Liu
Updates #1199 PiperOrigin-RevId: 332539197
2020-09-18Use a tmpfs file for shared anonymous and /dev/zero mmap on VFS2.Jamie Liu
This is more consistent with Linux (see comment on MM.NewSharedAnonMappable()). We don't do the same thing on VFS1 for reasons documented by the updated comment. PiperOrigin-RevId: 332514849
2020-09-18Remove SKIP_IF for now-supported features.Kevin Krakauer
Updates #3549. PiperOrigin-RevId: 332501660
2020-09-17{Set,Get} SO_LINGER on all endpoints.Nayana Bidari
SO_LINGER is a socket level option and should be stored on all endpoints even though it is used to linger only for TCP endpoints. PiperOrigin-RevId: 332369252
2020-09-17Complete vfs2 implementation of fallocate.Dean Deng
This change includes overlay, special regular gofer files, and hostfs. Fixes #3589. PiperOrigin-RevId: 332330860
2020-09-17Deflake vdso_clock_gettime test.Jamie Liu
PiperOrigin-RevId: 332281930
2020-09-16Automated rollback of changelist 329526153Nayana Bidari
PiperOrigin-RevId: 332097286
2020-09-16Receive broadcast packets on interested endpointsGhanan Gowripalan
When a broadcast packet is received by the stack, the packet should be delivered to each endpoint that may be interested in the packet. This includes all any address and specified broadcast address listeners. Test: integration_test.TestReuseAddrAndBroadcast PiperOrigin-RevId: 332060652
2020-09-15Enable automated marshalling for the syscall package.Rahat Mahmood
PiperOrigin-RevId: 331940975
2020-09-15Support setting STATX_SIZE for kernfs.InodeAttrs.Dean Deng
Make setting STATX_SIZE a no-op, if it is valid for the given permissions and file type. Also update proc tests, which were overfitted before. Fixes #3842. Updates #1193. PiperOrigin-RevId: 331861087
2020-09-15Merge pull request #3895 from btw616:fix/issue-3894gVisor bot
PiperOrigin-RevId: 331824411
2020-09-15Fix proc.(*fdDir).IterDirents for VFS2Tiwei Bie
Currently the returned offset is an index, and we can't use it to find the next fd to serialize, because getdents should iterate correctly despite mutation of fds. Instead, we can return the next fd to serialize plus 2 (which accounts for "." and "..") as the offset. Fixes: #3894 Signed-off-by: Tiwei Bie <tiwei.btw@antgroup.com>
2020-09-11Check that we have access to the trusted.* xattr namespace directly.Nicolas Lacasse
These operations require CAP_SYS_ADMIN in the root user namespace. There's no easy way to check that other than trying the operation and seeing what happens. PiperOrigin-RevId: 331242256
2020-09-10[vfs] Disable inode number equality check for overlayfs.Ayush Ranjan
Overlayfs does not persist a directory's inode number even while it is mounted. See fs/overlayfs/inode.c:ovl_map_dev_ino(). VFS2 generates a new inode number for directories everytime in lookup. PiperOrigin-RevId: 331045037
2020-09-10[vfs] Disable nlink tests for overlayfs.Ayush Ranjan
Overlayfs intentionally does not compute nlink for directories (because it can be really expensive). Linux returns 1, VFS2 returns 2 and VFS1 actually calculates the correct value. PiperOrigin-RevId: 330967139
2020-09-08[vfs] overlayfs: Fix socket tests.Ayush Ranjan
- BindSocketThenOpen test was expecting the incorrect error when opening a socket. Fixed that. - VirtualFilesystem.BindEndpointAt should not require pop.Path.Begin.Ok() because the filesystem implementations do not need to walk to the parent dentry. This check also exists for MknodAt, MkdirAt, RmdirAt, SymlinkAt and UnlinkAt but those filesystem implementations also need to walk to the parent denty. So that check is valid. Added some syscall tests to test this. PiperOrigin-RevId: 330625220
2020-09-08[vfs] Capitalize x in the {Get/Set/Remove/List}xattr functions.Ayush Ranjan
PiperOrigin-RevId: 330554450
2020-09-02Fix Accept to not return error for sockets in accept queue.Bhasker Hariharan
Accept on gVisor will return an error if a socket in the accept queue was closed before Accept() was called. Linux will return the new fd even if the returned socket is already closed by the peer say due to a RST being sent by the peer. This seems to be intentional in linux more details on the github issue. Fixes #3780 PiperOrigin-RevId: 329828404
2020-09-01Fix statfs test for opensource.Zach Koopmans
PiperOrigin-RevId: 329638946
2020-09-01Test opening file handles with different permissions.Dean Deng
These were problematic for vfs2 gofers before correctly implementing separate read/write handles. PiperOrigin-RevId: 329613261
2020-09-01Refactor tty codebase to use master-replica terminology.Ayush Ranjan
Updates #2972 PiperOrigin-RevId: 329584905
2020-09-01Automated rollback of changelist 328350576Nayana Bidari
PiperOrigin-RevId: 329526153
2020-08-31Remove __fuchsia__ definesTamir Duberstein
These mostly guard linux-only headers; check for linux instead. PiperOrigin-RevId: 329362762
2020-08-28Don't bind loopback to all IPs in an IPv6 subnetGhanan Gowripalan
An earlier change considered the loopback bound to all addresses in an assigned subnet. This should have only be done for IPv4 to maintain compatability with Linux: ``` $ ip addr show dev lo 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group ... link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever $ ping 2001:db8::1 PING 2001:db8::1(2001:db8::1) 56 data bytes ^C --- 2001:db8::1 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3062ms $ ping 2001:db8::2 PING 2001:db8::2(2001:db8::2) 56 data bytes ^C --- 2001:db8::2 ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2030ms $ sudo ip addr add 2001:db8::1/64 dev lo $ ping 2001:db8::1 PING 2001:db8::1(2001:db8::1) 56 data bytes 64 bytes from 2001:db8::1: icmp_seq=1 ttl=64 time=0.055 ms 64 bytes from 2001:db8::1: icmp_seq=2 ttl=64 time=0.074 ms 64 bytes from 2001:db8::1: icmp_seq=3 ttl=64 time=0.073 ms 64 bytes from 2001:db8::1: icmp_seq=4 ttl=64 time=0.071 ms ^C --- 2001:db8::1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3075ms rtt min/avg/max/mdev = 0.055/0.068/0.074/0.007 ms $ ping 2001:db8::2 PING 2001:db8::2(2001:db8::2) 56 data bytes From 2001:db8::1 icmp_seq=1 Destination unreachable: No route From 2001:db8::1 icmp_seq=2 Destination unreachable: No route From 2001:db8::1 icmp_seq=3 Destination unreachable: No route From 2001:db8::1 icmp_seq=4 Destination unreachable: No route ^C --- 2001:db8::2 ping statistics --- 4 packets transmitted, 0 received, +4 errors, 100% packet loss, time 3070ms ``` Test: integration_test.TestLoopbackAcceptAllInSubnet PiperOrigin-RevId: 329011566
2020-08-28Implement StatFS for various VFS2 filesystems.Rahat Mahmood
This mainly involved enabling kernfs' client filesystems to provide a StatFS implementation. Fixes #3411, #3515. PiperOrigin-RevId: 329009864
2020-08-28Fix EOF handling for splice.Dean Deng
Also, add corresponding EOF tests for splice/sendfile. Discovered by syzkaller. PiperOrigin-RevId: 328975990
2020-08-28fix panic when calling SO_ORIGINAL_DST without initializing iptablesKevin Krakauer
Reported-by: syzbot+074ec22c42305725b79f@syzkaller.appspotmail.com PiperOrigin-RevId: 328963899
2020-08-28Add test demonstrating accept bugTamir Duberstein
Updates #3780. PiperOrigin-RevId: 328922573
2020-08-27Fix vfs2 pipe behavior when splicing to a non-pipe.Dean Deng
Fixes *.sh Java runtime tests, where splice()-ing from a pipe to /dev/zero would not actually empty the pipe. There was no guarantee that the data would actually be consumed on a splice operation unless the output file's implementation of Write/PWrite actually called VFSPipeFD.CopyIn. Now, whatever bytes are "written" are consumed regardless of whether CopyIn is called or not. Furthermore, the number of bytes in the IOSequence for reads is now capped at the amount of data actually available. Before, splicing to /dev/zero would always return the requested splice size without taking the actual available data into account. This change also refactors the case where an input file is spliced into an output pipe so that it follows a similar pattern, which is arguably cleaner anyway. Updates #3576. PiperOrigin-RevId: 328843954
2020-08-27unix: return ECONNREFUSE if a socket file exists but a socket isn't bound to itAndrei Vagin
PiperOrigin-RevId: 328843560
2020-08-27Merge pull request #3077 from jinmouil:beef-write-syscallgVisor bot
PiperOrigin-RevId: 328824023
2020-08-27Fix BadSocketPair for open source.Zach Koopmans
BadSocketPair test will return several errnos (EPREM, ESOCKTNOSUPPORT, EAFNOSUPPORT) meaning the test is just too specific. Checking the syscall fails is appropriate. PiperOrigin-RevId: 328813071
2020-08-27Skip IPv6UDPUnboundSocketNetlinkTest on native linuxGhanan Gowripalan
...while we figure out of we want to consider the loopback interface bound to all IPs in an assigned IPv6 subnet, or not (to maintain compatibility with Linux). PiperOrigin-RevId: 328807974
2020-08-27ip6tables: (de)serialize ip6tables structsKevin Krakauer
More implementation+testing to follow. #3549. PiperOrigin-RevId: 328770160
2020-08-27Fix JobControl tests for open source.Zach Koopmans
ioctl calls with TIOCSCTTY fail if the calling process already has a controlling terminal, which occurs on a 5.4 kernel like our Ubuntu 18 CI. Thus, run tests calling ioctl TTOCSCTTY in clean subprocess. Also, while we're here, switch out non-inclusive master/slave for main/replica. PiperOrigin-RevId: 328756598
2020-08-26beef up write syscall testsJinmou Li
Added a few tests for write(2) and pwrite(2) 1. Regular Files For write(2) - write zero bytes should not move the offset - write non-zero bytes should increment the offset the exact amount - write non-zero bytes after a lseek() should move the offset the exact amount after the seek - write non-zero bytes with O_APPEND should move the offset the exact amount after original EOF For pwrite(2), offset is not affected when - pwrite zero bytes - pwrite non-zero bytes For EOF, added a test asserting the EOF (indicated by lseek(SEEK_END)) is updated properly after writing non-zero bytes 2. Symlink Added one pwite64() call for symlink that is written as a counterpart of the existing test using pread64()
2020-08-26tmpfs: Allow xattrs in the trusted namespace if creds has CAP_SYS_ADMIN.Nicolas Lacasse
This is needed to support the overlay opaque attribute. PiperOrigin-RevId: 328552985
2020-08-25Fix SocketPairTest and BadSocketPairTest in opensource.Zach Koopmans
PiperOrigin-RevId: 328467152
2020-08-25Expose basic coverage information to userspace through kcov interface.Dean Deng
In Linux, a kernel configuration is set that compiles the kernel with a custom function that is called at the beginning of every basic block, which updates the memory-mapped coverage information. The Go coverage tool does not allow us to inject arbitrary instructions into basic blocks, but it does provide data that we can convert to a kcov-like format and transfer them to userspace through a memory mapping. Note that this is not a strict implementation of kcov, which is especially tricky to do because we do not have the same coverage tools available in Go that that are available for the actual Linux kernel. In Linux, a kernel configuration is set that compiles the kernel with a custom function that is called at the beginning of every basic block to write program counters to the kcov memory mapping. In Go, however, coverage tools only give us a count of basic blocks as they are executed. Every time we return to userspace, we collect the coverage information and write out PCs for each block that was executed, providing userspace with the illusion that the kcov data is always up to date. For convenience, we also generate a unique synthetic PC for each block instead of using actual PCs. Finally, we do not provide thread-specific coverage data (each kcov instance only contains PCs executed by the thread owning it); instead, we will supply data for any file specified by -- instrumentation_filter. Also, fix issue in nogo that was causing pkg/coverage:coverage_nogo compilation to fail. PiperOrigin-RevId: 328426526
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-29 15:33:56 +0000