| Age | Commit message (Collapse) | Author |
|---|
|
PiperOrigin-RevId: 336304024
|
|
When a response needs to be sent to an incoming packet, the stack should
consult its neighbour table to determine the remote address's link
address.
When an entry does not exist in the stack's neighbor table, the stack
should queue the packet while link resolution completes. See comments.
PiperOrigin-RevId: 336185457
|
|
The IPv4 RFCs are specific (though obtuse) that an echo response
packet needs to contain all the options from the echo request,
much as if it been routed back to the sender, though apparently
with a new TTL. They suggest copying the incoming packet header
to achieve this so that is what this patch does.
PiperOrigin-RevId: 335559176
|
|
Linux doesn't generate a link-local address for the loopback interface.
Test: integration_test.TestInitialLoopbackAddresses
PiperOrigin-RevId: 334453182
|
|
Network or transport protocols may want to reach the stack. Support this
by letting the stack create the protocol instances so it can pass a
reference to itself at protocol creation time.
Note, protocols do not yet use the stack in this CL but later CLs will
make use of the stack from protocols.
PiperOrigin-RevId: 334260210
|
|
The lifetime of addreses in a loopback interface's associated subnets
should be bound to their respective permanent addresses.
This change also fixes a race when the stack attempts to get an IPv4
rereferencedNetworkEndpoint for an address in an associated subnet on
a loopback interface. Before this change, the stack would only check
if an IPv4 address is contained in an associated subnet while holding
a read lock but wouldn't do this same check after releasing the read
lock for a write lock to create a temporary address. This may cause
the stack to bind the lifetime of the address to a new (temporary)
endpoint instead of the associated subnet's permanent address.
Test: integration_test.TestLoopbackSubnetLifetimeBoundToAddr
PiperOrigin-RevId: 332094719
|
|
When a broadcast packet is received by the stack, the packet should be
delivered to each endpoint that may be interested in the packet. This
includes all any address and specified broadcast address listeners.
Test: integration_test.TestReuseAddrAndBroadcast
PiperOrigin-RevId: 332060652
|
|
An earlier change considered the loopback bound to all addresses in an
assigned subnet. This should have only be done for IPv4 to maintain
compatability with Linux:
```
$ ip addr show dev lo
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group ...
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
$ ping 2001:db8::1
PING 2001:db8::1(2001:db8::1) 56 data bytes
^C
--- 2001:db8::1 ping statistics ---
4 packets transmitted, 0 received, 100% packet loss, time 3062ms
$ ping 2001:db8::2
PING 2001:db8::2(2001:db8::2) 56 data bytes
^C
--- 2001:db8::2 ping statistics ---
3 packets transmitted, 0 received, 100% packet loss, time 2030ms
$ sudo ip addr add 2001:db8::1/64 dev lo
$ ping 2001:db8::1
PING 2001:db8::1(2001:db8::1) 56 data bytes
64 bytes from 2001:db8::1: icmp_seq=1 ttl=64 time=0.055 ms
64 bytes from 2001:db8::1: icmp_seq=2 ttl=64 time=0.074 ms
64 bytes from 2001:db8::1: icmp_seq=3 ttl=64 time=0.073 ms
64 bytes from 2001:db8::1: icmp_seq=4 ttl=64 time=0.071 ms
^C
--- 2001:db8::1 ping statistics ---
4 packets transmitted, 4 received, 0% packet loss, time 3075ms
rtt min/avg/max/mdev = 0.055/0.068/0.074/0.007 ms
$ ping 2001:db8::2
PING 2001:db8::2(2001:db8::2) 56 data bytes
From 2001:db8::1 icmp_seq=1 Destination unreachable: No route
From 2001:db8::1 icmp_seq=2 Destination unreachable: No route
From 2001:db8::1 icmp_seq=3 Destination unreachable: No route
From 2001:db8::1 icmp_seq=4 Destination unreachable: No route
^C
--- 2001:db8::2 ping statistics ---
4 packets transmitted, 0 received, +4 errors, 100% packet loss, time 3070ms
```
Test: integration_test.TestLoopbackAcceptAllInSubnet
PiperOrigin-RevId: 329011566
|
|
When a loopback interface is configurd with an address and associated
subnet, the loopback should treat all addresses in that subnet as an
address it owns.
This is mimicking linux behaviour as seen below:
```
$ ip addr show dev lo
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group ...
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
$ ping 192.0.2.1
PING 192.0.2.1 (192.0.2.1) 56(84) bytes of data.
^C
--- 192.0.2.1 ping statistics ---
2 packets transmitted, 0 received, 100% packet loss, time 1018ms
$ ping 192.0.2.2
PING 192.0.2.2 (192.0.2.2) 56(84) bytes of data.
^C
--- 192.0.2.2 ping statistics ---
3 packets transmitted, 0 received, 100% packet loss, time 2039ms
$ sudo ip addr add 192.0.2.1/24 dev lo
$ ip addr show dev lo
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group ...
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet 192.0.2.1/24 scope global lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
$ ping 192.0.2.1
PING 192.0.2.1 (192.0.2.1) 56(84) bytes of data.
64 bytes from 192.0.2.1: icmp_seq=1 ttl=64 time=0.131 ms
64 bytes from 192.0.2.1: icmp_seq=2 ttl=64 time=0.046 ms
64 bytes from 192.0.2.1: icmp_seq=3 ttl=64 time=0.048 ms
^C
--- 192.0.2.1 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2042ms
rtt min/avg/max/mdev = 0.046/0.075/0.131/0.039 ms
$ ping 192.0.2.2
PING 192.0.2.2 (192.0.2.2) 56(84) bytes of data.
64 bytes from 192.0.2.2: icmp_seq=1 ttl=64 time=0.131 ms
64 bytes from 192.0.2.2: icmp_seq=2 ttl=64 time=0.069 ms
64 bytes from 192.0.2.2: icmp_seq=3 ttl=64 time=0.049 ms
64 bytes from 192.0.2.2: icmp_seq=4 ttl=64 time=0.035 ms
^C
--- 192.0.2.2 ping statistics ---
4 packets transmitted, 4 received, 0% packet loss, time 3049ms
rtt min/avg/max/mdev = 0.035/0.071/0.131/0.036 ms
```
Test: integration_test.TestLoopbackAcceptAllInSubnet
PiperOrigin-RevId: 328188546
|
|
Formerly, when a packet is constructed or parsed, all headers are set by the
client code. This almost always involved prepending to pk.Header buffer or
trimming pk.Data portion. This is known to prone to bugs, due to the complexity
and number of the invariants assumed across netstack to maintain.
In the new PacketHeader API, client will call Push()/Consume() method to
construct/parse an outgoing/incoming packet. All invariants, such as slicing
and trimming, are maintained by the API itself.
NewPacketBuffer() is introduced to create new PacketBuffer. Zero value is no
longer valid.
PacketBuffer now assumes the packet is a concatenation of following portions:
* LinkHeader
* NetworkHeader
* TransportHeader
* Data
Any of them could be empty, or zero-length.
PiperOrigin-RevId: 326507688
|
|
Packets MUST NOT use a non-unicast source address for ICMP
Echo Replies.
Test: integration_test.TestPingMulticastBroadcast
PiperOrigin-RevId: 325634380
|
|
Test:
- stack_test.TestJoinLeaveMulticastOnNICEnableDisable
- integration_test.TestIncomingMulticastAndBroadcast
PiperOrigin-RevId: 325185259
|
|
Test: integration_test.TestIncomingSubnetBroadcast
PiperOrigin-RevId: 325135617
|
