summaryrefslogtreecommitdiffhomepage
path: root/pkg/tcpip/stack
AgeCommit message (Collapse)Author
2019-10-16Do Duplicate Address Detection on permanent IPv6 addresses.Ghanan Gowripalan
This change adds support for Duplicate Address Detection on IPv6 addresses as defined by RFC 4862 section 5.4. Note, this change will not break existing uses of netstack as the default configuration for the stack options is set in such a way that DAD will not be performed. See `stack.Options` and `stack.NDPConfigurations` for more details. Tests: Tests to make sure that the DAD process properly resolves or fails. That is, tests make sure that DAD resolves only if: - No other node is performing DAD for the same address - No other node owns the same address PiperOrigin-RevId: 275189471
2019-10-15Set NDP hop limit in accordance with RFC 4861Tamir Duberstein
...and do not populate link address cache at dispatch. This partially reverts 313c767b0001bf6271405f1b765b60a334d6e911, which caused malformed packets (e.g. NDP Neighbor Adverts with incorrect hop limit values) to populate the address cache. In particular, this masked a bug that was introduced to the Neighbor Advert generation code in 7c1587e3401a010d1865df61dbaf117c77dd062e. PiperOrigin-RevId: 274865182
2019-10-14Internal change.gVisor bot
PiperOrigin-RevId: 274700093
2019-10-14Reorder BUILD license and load functions in netstack.Kevin Krakauer
PiperOrigin-RevId: 274672346
2019-10-09Internal change.gVisor bot
PiperOrigin-RevId: 273861936
2019-10-07Implement IP_TTL.Ian Gudger
Also change the default TTL to 64 to match Linux. PiperOrigin-RevId: 273430341
2019-10-03Implement proper local broadcast behaviorChris Kuiper
The behavior for sending and receiving local broadcast (255.255.255.255) traffic is as follows: Outgoing -------- * A broadcast packet sent on a socket that is bound to an interface goes out that interface * A broadcast packet sent on an unbound socket follows the route table to select the outgoing interface + if an explicit route entry exists for 255.255.255.255/32, use that one + else use the default route * Broadcast packets are looped back and delivered following the rules for incoming packets (see next). This is the same behavior as for multicast packets, except that it cannot be disabled via sockopt. Incoming -------- * Sockets wishing to receive broadcast packets must bind to either INADDR_ANY (0.0.0.0) or INADDR_BROADCAST (255.255.255.255). No other socket receives broadcast packets. * Broadcast packets are multiplexed to all sockets matching it. This is the same behavior as for multicast packets. * A socket can bind to 255.255.255.255:<port> and then receive its own broadcast packets sent to 255.255.255.255:<port> In addition, this change implicitly fixes an issue with multicast reception. If two sockets want to receive a given multicast stream and one is bound to ANY while the other is bound to the multicast address, only one of them will receive the traffic. PiperOrigin-RevId: 272792377
2019-09-30Fix bugs in PickEphemeralPort for TCP.Bhasker Hariharan
Netstack always picks a random start point everytime PickEphemeralPort is called. While this is required for UDP so that DNS requests go out through a randomized set of ports it is not required for TCP. Infact Linux explicitly hashes the (srcip, dstip, dstport) and a one time secret initialized at start of the application to get a random offset. But to ensure it doesn't start from the same point on every scan it uses a static hint that is incremented by 2 in every call to pick ephemeral ports. The reason for 2 is Linux seems to split the port ranges where active connects seem to use even ones while odd ones are used by listening sockets. This CL implements a similar strategy where we use a hash + hint to generate the offset to start the search for a free Ephemeral port. This ensures that we cycle through the available port space in order for repeated connects to the same destination and significantly reduces the chance of picking a recently released port. PiperOrigin-RevId: 272058370
2019-09-27Implement SO_BINDTODEVICE sockoptgVisor bot
PiperOrigin-RevId: 271644926
2019-09-25Remove centralized registration of protocols.Kevin Krakauer
Also removes the need for protocol names. PiperOrigin-RevId: 271186030
2019-09-24Return only primary addresses in Stack.NICInfo()Chris Kuiper
Non-primary addresses are used for endpoints created to accept multicast and broadcast packets, as well as "helper" endpoints (0.0.0.0) that allow sending packets when no proper address has been assigned yet (e.g., for DHCP). These addresses are not real addresses from a user point of view and should not be part of the NICInfo() value. Also see b/127321246 for more info. This switches NICInfo() to call a new NIC.PrimaryAddresses() function. To still allow an option to get all addresses (mostly for testing) I added Stack.GetAllAddresses() and NIC.AllAddresses(). In addition, the return value for GetMainNICAddress() was changed for the case where the NIC has no primary address. Instead of returning an error here, it now returns an empty AddressWithPrefix() value. The rational for this change is that it is a valid case for a NIC to have no primary addresses. Lastly, I refactored the code based on the new additions. PiperOrigin-RevId: 270971764
2019-09-24Simplify ICMPRateLimiterTamir Duberstein
https://github.com/golang/time/commit/c4c64ca added SetBurst upstream. PiperOrigin-RevId: 270925077
2019-09-23netstack: convert more socket options to {Set,Get}SockOptIntAndrei Vagin
PiperOrigin-RevId: 270763208
2019-09-20Allow waiting for LinkEndpoint worker goroutines to finish.Ian Gudger
Previously, the only safe way to use an fdbased endpoint was to leak the FD. This change makes it possible to safely close the FD. This is the first step towards having stoppable stacks. Updates #837 PiperOrigin-RevId: 270346582
2019-09-17Automated rollback of changelist 268047073Ghanan Gowripalan
PiperOrigin-RevId: 269658971
2019-09-12Implement splice methods for pipes and sockets.Adin Scannell
This also allows the tee(2) implementation to be enabled, since dup can now be properly supported via WriteTo. Note that this change necessitated some minor restructoring with the fs.FileOperations splice methods. If the *fs.File is passed through directly, then only public API methods are accessible, which will deadlock immediately since the locking is already done by fs.Splice. Instead, we pass through an abstract io.Reader or io.Writer, which elide locks and use the underlying fs.FileOperations directly. PiperOrigin-RevId: 268805207
2019-09-12Remove go_test from go_stateify and go_marshalMichael Pratt
They are no-ops, so the standard rule works fine. PiperOrigin-RevId: 268776264
2019-09-12Automated rollback of changelist 268047073Ghanan Gowripalan
PiperOrigin-RevId: 268757842
2019-09-09Join IPv6 all-nodes and solicited-node multicast addresses where appropriate.Ghanan Gowripalan
The IPv6 all-nodes multicast address will be joined on NIC enable, and the appropriate IPv6 solicited-node multicast address will be joined when IPv6 addresses are added. Tests: Test receiving packets destined to the IPv6 link-local all-nodes multicast address and the IPv6 solicted node address of an added IPv6 address. PiperOrigin-RevId: 268047073
2019-09-06Remove reundant global tcpip.LinkEndpointID.Ian Gudger
PiperOrigin-RevId: 267709597
2019-09-04Handle subnet and broadcast addresses correctly with NIC.subnetsChris Kuiper
This also renames "subnet" to "addressRange" to avoid any more confusion with an interface IP's subnet. Lastly, this also removes the Stack.ContainsSubnet(..) API since it isn't used by anyone. Plus the same information can be obtained from Stack.NICAddressRanges(). PiperOrigin-RevId: 267229843
2019-09-03Make UDP traceroute work.Bhasker Hariharan
Adds support to generate Port Unreachable messages for UDP datagrams received on a port for which there is no valid endpoint. Fixes #703 PiperOrigin-RevId: 267034418
2019-08-30Fix data race accessing referencedNetworkEndpoint.kindChris Kuiper
Wrapping "kind" into atomic access functions. Fixes #789 PiperOrigin-RevId: 266485501
2019-08-28Export generated linkAddrEntryEntryTamir Duberstein
PiperOrigin-RevId: 266000128
2019-08-27Populate link address cache at dispatchTamir Duberstein
This allows the stack to learn remote link addresses on incoming packets, reducing the need to ARP to send responses. This also reduces the number of round trips to the system clock, since that may also prove to be performance-sensitive. Fixes #739. PiperOrigin-RevId: 265815816
2019-08-26Prevent a network endpoint to send/rcv if its address was removedChris Kuiper
This addresses the problem where an endpoint has its address removed but still has outstanding references held by routes used in connected TCP/UDP sockets which prevent the removal of the endpoint. The fix adds a new "expired" flag to the referenced network endpoint, which is set when an endpoint has its address removed. Incoming packets are not delivered to an expired endpoint (unless in promiscuous mode), while sending outgoing packets triggers an error to the caller (unless in spoofing mode). In addition, a few helper functions were added to stack_test.go to reduce code duplications. PiperOrigin-RevId: 265514326
2019-08-21Use tcpip.Subnet in tcpip.RouteTamir Duberstein
This is the first step in replacing some of the redundant types with the standard library equivalents. PiperOrigin-RevId: 264706552
2019-08-16netstack: disconnect an unix socket only if the address family is AF_UNSPECAndrei Vagin
Linux allows to call connect for ANY and the zero port. PiperOrigin-RevId: 263892534
2019-08-16Add subnet checking to NIC.findEndpoint and consolidate with NIC.getRefChris Kuiper
This adds the same logic to NIC.findEndpoint that is already done in NIC.getRef. Since this makes the two functions very similar they were combined into one with the originals being wrappers. PiperOrigin-RevId: 263864708
2019-08-14Replace uinptr with int64 when returning lengthsTamir Duberstein
This is in accordance with newer parts of the standard library. PiperOrigin-RevId: 263449916
2019-08-08netstack: Don't start endpoint goroutines too soon on restore.Rahat Mahmood
Endpoint protocol goroutines were previously started as part of loading the endpoint. This is potentially too soon, as resources used by these goroutine may not have been loaded. Protocol goroutines may perform meaningful work as soon as they're started (ex: incoming connect) which can cause them to indirectly access resources that haven't been loaded yet. This CL defers resuming all protocol goroutines until the end of restore. PiperOrigin-RevId: 262409429
2019-08-02Plumbing for iptables sockopts.Kevin Krakauer
PiperOrigin-RevId: 261413396
2019-08-02Automated rollback of changelist 261191548Rahat Mahmood
PiperOrigin-RevId: 261373749
2019-08-01Implement getsockopt(TCP_INFO).Rahat Mahmood
Export some readily-available fields for TCP_INFO and stub out the rest. PiperOrigin-RevId: 261191548
2019-07-30Pass ProtocolAddress instead of its fieldsTamir Duberstein
PiperOrigin-RevId: 260803517
2019-07-24Add support for a subnet prefix length on interface network addressesChris Kuiper
This allows the user code to add a network address with a subnet prefix length. The prefix length value is stored in the network endpoint and provided back to the user in the ProtocolAddress type. PiperOrigin-RevId: 259807693
2019-07-18net/tcp/setockopt: impelment setsockopt(fd, SOL_TCP, TCP_INQ)Andrei Vagin
PiperOrigin-RevId: 258859507
2019-07-12Add IPPROTO_RAW, which allows raw sockets to write IP headers.Kevin Krakauer
iptables also relies on IPPROTO_RAW in a way. It opens such a socket to manipulate the kernel's tables, but it doesn't actually use any of the functionality. Blegh. PiperOrigin-RevId: 257903078
2019-06-13Add support for TCP receive buffer auto tuning.Bhasker Hariharan
The implementation is similar to linux where we track the number of bytes consumed by the application to grow the receive buffer of a given TCP endpoint. This ensures that the advertised window grows at a reasonable rate to accomodate for the sender's rate and prevents large amounts of data being held in stack buffers if the application is not actively reading or not reading fast enough. The original paper that was used to implement the linux receive buffer auto- tuning is available @ https://public.lanl.gov/radiant/pubs/drs/lacsi2001.pdf NOTE: Linux does not implement DRS as defined in that paper, it's just a good reference to understand the solution space. Updates #230 PiperOrigin-RevId: 253168283
2019-06-13Update canonical repository.Adin Scannell
This can be merged after: https://github.com/google/gvisor-website/pull/77 or https://github.com/google/gvisor-website/pull/78 PiperOrigin-RevId: 253132620
2019-06-06Track and export socket state.Rahat Mahmood
This is necessary for implementing network diagnostic interfaces like /proc/net/{tcp,udp,unix} and sock_diag(7). For pass-through endpoints such as hostinet, we obtain the socket state from the backend. For netstack, we add explicit tracking of TCP states. PiperOrigin-RevId: 251934850
2019-06-05Adjust route when looping multicast packetsChris Kuiper
Multicast packets are special in that their destination address does not identify a specific interface. When sending out such a packet the multicast address is the remote address, but for incoming packets it is the local address. Hence, when looping a multicast packet, the route needs to be tweaked to reflect this. PiperOrigin-RevId: 251739298
2019-05-24Remove unused wakersTamir Duberstein
These wakers are uselessly allocated and passed around; nothing ever listens for notifications on them. The code here appears to be vestigial, so removing it and allowing a nil waker to be passed seems appropriate. PiperOrigin-RevId: 249879320 Change-Id: Icd209fb77cc0dd4e5c49d7a9f2adc32bf88b4b71
2019-05-22UDP and TCP raw socket support.Kevin Krakauer
PiperOrigin-RevId: 249511348 Change-Id: I34539092cc85032d9473ff4dd308fc29dc9bfd6b
2019-05-03Implement support for SACK based recovery(RFC 6675).Bhasker Hariharan
PiperOrigin-RevId: 246536003 Change-Id: I118b745f45040be9c70cb6a1028acdb06c78d8c9
2019-05-03Proper cleanup of sockets that used REUSEPORTChris Kuiper
Fixed a small logic error that broke proper accounting of MultiPortEndpoints. PiperOrigin-RevId: 246502126 Change-Id: I1a7d6ea134f811612e545676212899a3707bc2c2
2019-05-02Support reception of multicast data on more than one socketChris Kuiper
This requires two changes: 1) Support for more than one socket to join a given multicast group. 2) Duplicate delivery of incoming multicast packets to all sockets listening for it. In addition, I tweaked the code (and added a test) to disallow duplicates IP_ADD_MEMBERSHIP calls for the same group and NIC. This is how Linux does it. PiperOrigin-RevId: 246437315 Change-Id: Icad8300b4a8c3f501d9b4cd283bd3beabef88b72
2019-04-29Change copyright notice to "The gVisor Authors"Michael Pratt
Based on the guidelines at https://opensource.google.com/docs/releasing/authors/. 1. $ rg -l "Google LLC" | xargs sed -i 's/Google LLC.*/The gVisor Authors./' 2. Manual fixup of "Google Inc" references. 3. Add AUTHORS file. Authors may request to be added to this file. 4. Point netstack AUTHORS to gVisor AUTHORS. Drop CONTRIBUTORS. Fixes #209 PiperOrigin-RevId: 245823212 Change-Id: I64530b24ad021a7d683137459cafc510f5ee1de9
2019-04-29Allow and document bug ids in gVisor codebase.Nicolas Lacasse
PiperOrigin-RevId: 245818639 Change-Id: I03703ef0fb9b6675955637b9fe2776204c545789
2019-04-26Make raw sockets a toggleable feature disabled by default.Kevin Krakauer
PiperOrigin-RevId: 245511019 Change-Id: Ia9562a301b46458988a6a1f0bbd5f07cbfcb0615
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-22 23:18:05 +0000