Age | Commit message (Collapse) | Author |
|
|
|
Updates #6441,#6317
PiperOrigin-RevId: 404872327
|
|
|
|
..including ICMP headers before delivering them to the
TransportDispatcher.
Updates #3810.
PiperOrigin-RevId: 404404002
|
|
|
|
...to match Linux behaviour.
We can see evidence of Linux representing loopback as an ethernet-based
device below:
```
# EUI-48 based MAC addresses.
$ ip link show lo
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
# tcpdump showing ethernet frames when sniffing loopback and logging the
# link-type as EN10MB (Ethernet).
$ sudo tcpdump -i lo -e -c 2 -n
tcpdump: verbose output suppressed, use -v[v]... for full protocol decode
listening on lo, link-type EN10MB (Ethernet), snapshot length 262144 bytes
03:09:05.002034 00:00:00:00:00:00 > 00:00:00:00:00:00, ethertype IPv4 (0x0800), length 66: 127.0.0.1.9557 > 127.0.0.1.36828: Flags [.], ack 3562800815, win 15342, options [nop,nop,TS val 843174495 ecr 843159493], length 0
03:09:05.002094 00:00:00:00:00:00 > 00:00:00:00:00:00, ethertype IPv4 (0x0800), length 66: 127.0.0.1.36828 > 127.0.0.1.9557: Flags [.], ack 1, win 6160, options [nop,nop,TS val 843174496 ecr 843159493], length 0
2 packets captured
116 packets received by filter
0 packets dropped by kernel
```
Wireshark shows a similar result as the tcpdump example above.
Linux's loopback setup: https://github.com/torvalds/linux/blob/5bfc75d92efd494db37f5c4c173d3639d4772966/drivers/net/loopback.c#L162
PiperOrigin-RevId: 391836719
|
|
|
|
PiperOrigin-RevId: 382427879
|
|
|
|
This change prepares for a later change which supports the NDP
Route Information option to discover more-specific routes, as
per RFC 4191.
Updates #6172.
PiperOrigin-RevId: 382225812
|
|
|
|
...instead of calculating a fresh checksum to avoid re-calcalculating
a checksum on unchanged bytes.
Fixes #5340.
PiperOrigin-RevId: 381403888
|
|
|
|
Updates #5940.
PiperOrigin-RevId: 380668609
|
|
|
|
This change prepares for a later change which actually handles the
Prf field in RAs to discover default routers with preference values,
as per RFC 4191.
Updates #6172.
Test: header_test.TestNDPRouterAdvert
PiperOrigin-RevId: 379421710
|
|
|
|
- Typos
- Unused arguments
- Useless conversions
PiperOrigin-RevId: 376362730
|
|
|
|
PiperOrigin-RevId: 376001032
|
|
|
|
Introduce tcpip.MonotonicTime; replace int64 in tcpip.Clock method
returns with time.Time and MonotonicTime to improve type safety and
ensure that monotonic clock readings are never compared to wall clock
readings.
PiperOrigin-RevId: 375775907
|
|
|
|
- Unused constants
- Unused functions
- Unused arguments
- Unkeyed literals
- Unnecessary conversions
PiperOrigin-RevId: 375253464
|
|
|
|
Benchmark iperf3:
Before After
native->runsc 5.14 5.01 (Gbps)
runsc->native 4.15 4.07 (Gbps)
It did introduce overhead, mainly at the bridge between pkg/buffer and
VectorisedView, the ExtractVV method. Once endpoints start migrating away from
VV, this overhead will be gone.
Updates #2404
PiperOrigin-RevId: 373651666
|
|
|
|
This is done for IPv4, UDP and TCP headers.
This also changes the packet checkers used in tests to error on
zero-checksum, not sure why it was allowed before.
And while I'm here, make comments' case consistent.
RELNOTES: n/a
Fixes #5049
PiperOrigin-RevId: 369383862
|
|
This was semi-automated -- there are many addresses that were not replaced.
Future commits should clean those up.
Parse4 and Parse6 were given their own package because //pkg/test can introduce
dependency cycles, as it depends transitively on //pkg/tcpip and some other
netstack packages.
PiperOrigin-RevId: 368726528
|
|
|
|
To match the V4 variant.
PiperOrigin-RevId: 367691981
|
|
|
|
As per RFC 3927 section 7 and RFC 4291 section 2.5.6.
Test: forward_test.TestMulticastForwarding
PiperOrigin-RevId: 367519336
|
|
|
|
See comments inline code for rationale.
Test: ip_test.TestJoinLeaveAllRoutersGroup
PiperOrigin-RevId: 367449434
|
|
|
|
...as per RFC 2710 section 5 page 10.
Test: ipv6_test.TestMLDSkipProtocol
PiperOrigin-RevId: 367031126
|
|
|
|
|
|
They are not used outside of the header package.
PiperOrigin-RevId: 363237708
|
|
|
|
...as per RFC 7527.
If a looped-back DAD message is received, do not fail DAD since our own
DAD message does not indicate that a neighbor has the address assigned.
Test: ndp_test.TestDADResolveLoopback
PiperOrigin-RevId: 363224288
|
|
|
|
- Implement Stringer for it so that we can improve error messages.
- Use TCPFlags through the code base. There used to be a mixed usage of byte,
uint8 and int as TCP flags.
PiperOrigin-RevId: 361940150
|
|
|
|
One of the preparation to decouple underlying buffer implementation.
There are still some methods that tie to VectorisedView, and they will be
changed gradually in later CLs.
This CL also introduce a new ICMPv6ChecksumParams to replace long list of
parameters when calling ICMPv6Checksum, aiming to be more descriptive.
PiperOrigin-RevId: 360778149
|
|
|
|
This change also adds support for Router Alert option processing on
incoming packets, a new stat for Router Alert option, and exports
all the IP-option related stats.
Fixes #5491
PiperOrigin-RevId: 358238123
|
|
|
|
...to remove the need for the transport layer to deduce the type of
error it received.
Rename HandleControlPacket to HandleError as HandleControlPacket only
handles errors.
tcpip.SockError now holds a tcpip.SockErrorCause interface that
different errors can implement.
PiperOrigin-RevId: 354994306
|