| Age | Commit message (Collapse) | Author |
|---|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PiperOrigin-RevId: 347047550
|
|
|
|
tcpip.ControlMessages can not contain Linux specific structures which makes it
painful to convert back and forth from Linux to tcpip back to Linux when passing
around control messages in hostinet and raw sockets.
Now we convert to the Linux version of the control message as soon as we are
out of tcpip.
PiperOrigin-RevId: 347027065
|
|
|
|
PiperOrigin-RevId: 346973338
|
|
|
|
Fixes #5004
PiperOrigin-RevId: 346643745
|
|
|
|
PiperOrigin-RevId: 345589628
|
|
|
|
These options allow overriding the signal that gets sent to the process when
I/O operations are available on the file descriptor, rather than the default
`SIGIO` signal. Doing so also populates `siginfo` to contain extra information
about which file descriptor caused the event (`si_fd`) and what events happened
on it (`si_band`). The logic around which FD is populated within `si_fd`
matches Linux's, which means it has some weird edge cases where that value may
not actually refer to a file descriptor that is still valid.
This CL also ports extra S/R logic regarding async handler in VFS2.
Without this, async I/O handlers aren't properly re-registered after S/R.
PiperOrigin-RevId: 345436598
|
|
|
|
As part of this, change Task.interrupted() to not drain Task.interruptChan, and
do so explicitly using new function Task.unsetInterrupted() instead.
PiperOrigin-RevId: 342768365
|
|
|
|
Closes #4746
PiperOrigin-RevId: 342747165
|
|
|
|
This reduces confusion with context.Context (which is also relevant to
kernel.Tasks) and is consistent with existing function kernel.LoadTaskImage().
PiperOrigin-RevId: 342167298
|
|
|
|
PiperOrigin-RevId: 341154192
|
|
|
|
Writes to pipes of size < PIPE_BUF are guaranteed to be atomic, so writes
larger than that will return EAGAIN if the pipe has capacity < PIPE_BUF.
Writes to eventfds will return EAGAIN if the write would cause the eventfd
value to go over the max.
In both such cases, calling Ready() on the FD will return true (because it is
possible to write), but specific kinds of writes will in fact return EAGAIN.
This CL fixes an infinite loop in splice and sendfile (VFS1 and VFS2) by
forcing skipping the readiness check for the outfile in send, splice, and tee.
PiperOrigin-RevId: 341102260
|
|
|
|
The default pipe size already matched linux, and is unchanged.
Furthermore `atomicIOBytes` is made a proper constant (as it is in Linux). We
were plumbing usermem.PageSize everywhere, so this is no functional change.
PiperOrigin-RevId: 340497006
|
|
|
|
PiperOrigin-RevId: 340389884
|
|
|
|
PiperOrigin-RevId: 339166854
|
|
|
|
- Check the sticky bit in overlay.filesystem.UnlinkAt(). Fixes
StickyTest.StickyBitPermDenied.
- When configuring a VFS2 overlay in runsc, copy the lower layer's root
owner/group/mode to the upper layer's root (as in the VFS1 equivalent,
boot.addOverlay()). This makes the overlay root owned by UID/GID 65534 with
mode 0755 rather than owned by UID/GID 0 with mode 01777. Fixes
CreateTest.CreateFailsOnUnpermittedDir, which assumes that the test cannot
create files in /.
- MknodTest.UnimplementedTypesReturnError assumes that the creation of device
special files is not supported. However, while the VFS2 gofer client still
doesn't support device special files, VFS2 tmpfs does, and in the overlay
test dimension mknod() targets a tmpfs upper layer. The test initially has
all capabilities, including CAP_MKNOD, so its creation of these files
succeeds. Constrain these tests to VFS1.
- Rename overlay.nonDirectoryFD to overlay.regularFileFD and only use it for
regular files, using the original FD for pipes and device special files. This
is more consistent with Linux (which gets the original inode_operations, and
therefore file_operations, for these file types from ovl_fill_inode() =>
init_special_inode()) and fixes remaining mknod and pipe tests.
- Read/write 1KB at a time in PipeTest.Streaming, rather than 4 bytes. This
isn't strictly necessary, but it makes the test less obnoxiously slow on
ptrace.
Fixes #4407
PiperOrigin-RevId: 337971042
|
|
|
|
Reported-by: syzbot+0268cc591c0f517a1de0@syzkaller.appspotmail.com
PiperOrigin-RevId: 337901664
|
|
|
|
This change makes the following changes:
- Unlocks MemoryFile.mu while calling mincore (checkCommitted) because mincore
can take a really long time. Accordingly looks up the segment in the tree
tree again and handles changes to the segment.
- MemoryFile.UpdateUsage() can now only be called at frequency at most 100Hz.
100 Hz = linux.CLOCKS_PER_SEC.
Co-authored-by: Jamie Liu <jamieliu@google.com>
PiperOrigin-RevId: 337865250
|
|
|
|
Control messages should be released on Read (which ignores the control message)
or zero-byte Send. Otherwise, open fds sent through the control messages will
be leaked.
PiperOrigin-RevId: 337110774
|
|
|
|
This fixes reference leaks related to accidentally forgetting to DecRef()
after calling one or the other.
PiperOrigin-RevId: 336918922
|
|
|
|
- sysinfo(2) does not actually require a fine-grained breakdown of memory
usage. Accordingly, instead of calling pgalloc.MemoryFile.UpdateUsage() to
update the sentry's fine-grained memory accounting snapshot, just use
pgalloc.MemoryFile.TotalUsage() (which is a single fstat(), and therefore far
cheaper).
- Use the number of threads in the root PID namespace (i.e. globally) rather
than in the task's PID namespace for consistency with Linux (which just reads
global variable nr_threads), and add a new method to kernel.PIDNamespace to
allow this to be read directly from an underlying map rather than requiring
the allocation and population of an intermediate slice.
PiperOrigin-RevId: 336353100
|
|
|
|
|
|
Reported-by: syzbot+bb82fb556d5d0a43f632@syzkaller.appspotmail.com
PiperOrigin-RevId: 336324720
|
|
|
