| Age | Commit message (Collapse) | Author |
|---|
|
|
|
This patch adds support for source-specific IPv6 routes to BIRD core.
This is based on Dean Luga's original patch, with the review comments
addressed. SADR support is added to network address parsing in confbase.Y
and to the kernel protocol on Linux.
Currently there is no way to mix source-specific and non-source-specific
routes (i.e., SADR tables cannot be connected to non-SADR tables).
Thanks to Toke Hoiland-Jorgensen for the original patch.
Minor changes by Ondrej Santiago Zajicek.
|
|
Internal table used for route learn was created with non-matching net
type for IPv6 kernel proto.
Thanks to Toke Hoiland-Jorgensen for the bugreport
|
|
|
|
On Linux, setting the ToS will also set the priority and the range of
accepted values is quite limited (masked by 0x1e). Therefore, 0xc0 is
translated to a priority of 0, not something we want, overriding the
"7" priority which was set previously explicitely. To avoid that, just
move setting priority later in the code.
Thanks to Vincent Bernat for the patch.
|
|
|
|
|
|
A filter should log messages only if executed explicitly (e.g., during
route export or route import). When a filter is executed for technical
reasons (e.g., to establish whether a route was exported before), it
should run silently.
|
|
|
|
Old way to set direct routes is to use local IP as gateway, but that does
not work properly on newer FreeBSDs. Now we use sockaddr_dl containing
interface index as gateway.
|
|
|
|
|
|
Based on patch from Pavel Tvrdik
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ECMP is not enabled on BSD, where it is not supported by BIRD.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Date/time output (e.g. in logs, show commands) can use %f to specify
subsecond time. By default, millisecond precision is used in output.
|
|
The old timer interface is still kept, but implemented by new timers. The
plan is to switch from the old inteface to the new interface, then clean
it up.
|
|
|
|
|
|
|
|
|
|
Also redesign preferred address selection and update protocols to use
appropriate preferred address.
Based on a previous work by Jan Maria Matejka.
|
|
Add basic VRF (virtual routing and forwarding) support. Protocols can be
associated with VRFs, such protocols will be restricted to interfaces
assigned to the VRF (as reported by Linux kernel) and will use sockets
bound to the VRF. E.g., different multihop BGP instances can use diffent
kernel routing tables to handle BGP TCP connections.
The VRF support is preliminary, currently there are several limitations:
- Recent Linux kernels (4.11) do not handle correctly sockets bound
to interaces that are part of VRF, so most protocols other than multihop
BGP do not work. This will be fixed by future kernel versions.
- Neighbor cache ignores VRFs. Breaks config with the same prefix on
local interfaces in different VRFs. Not much problem as single hop
protocols do not work anyways.
- Olock code ignores VRFs. Breaks config with multiple BGP peers with the
same IP address in different VRFs.
- Incoming BGP connections are not dispatched according to VRFs.
Breaks config with multiple BGP peers with the same IP address in
different VRFs. Perhaps we would need some kernel API to read VRF of
incoming connection? Or probably use multiple listening sockets in
int-new branch.
- We should handle master VRF interface up/down events and perhaps
disable associated protocols when VRF goes down. Or at least disable
associated interfaces.
- Also we should check if the master iface is really VRF iface and
not some other kind of master iface.
- BFD session request dispatch should be aware of VRFs.
- Perhaps kernel protocol should read default kernel table ID from VRF
iface so it is not necessary to configure it.
- Perhaps we should have per-VRF default table.
|
|
Starting from Linux 4.11, IPv6 ECMP routes are now notified using
RTA_MULTIPATH, like IPv4 ones. The patch adds support for RTA_MULTIPATH
parsing for IPv6 routes. This also enables to parse ECMP alien routes
correctly.
Thanks to Vincent Bernat for the original patch.
|
|
Incorrect structure alignment breaks kernel routing table updates on
FreeBSD/ARM (and perhaps other platforms).
Thanks to Eugene Sevastyanov for the original patch.
|
|
Add proper support for per-nexthop onlink flag in routes to handle next
hop addresses that are not covered by interface IP ranges. Supported by
kernel and static protocols.
Thanks to Vincent Bernat for the idea.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Replaced by constant compile-time expressions. CPU_STRUCT_ALIGN is not
really correct, but is consistent with the old behavior.
|
|
|
