| Age | Commit message (Collapse) | Author |
|---|
|
|
|
|
|
|
|
|
|
Remove assumption that main channel is the only channel.
|
|
Just use hello_expiry for that, keep init_expiry for initial
unauthentized neighbors.
|
|
Some cleanups and bugfixes to the previous patch, including:
- Fix rate limiting in index mismatch check
- Fix missing BABEL_AUTH_INDEX_LEN in auth_tx_overhead computation
- Fix missing auth_tx_overhead recalculation during reconfiguration
- Fix pseudoheader construction in babel_auth_sign() (sport vs fport)
- Fix typecasts for ptrdiffs in log messages
- Make auth log messages similar to corresponding RIP/OSPF ones
- Change auth log messages for events that happen during regular
operation to debug messages
- Switch meaning of babel_auth_check*() functions for consistency
with corresponding RIP/OSPF ones
- Remove requirement for min/max key length, only those required by
given MAC code are enforced
|
|
This implements support for MAC authentication in the Babel protocol, as
specified by RFC 8967. The implementation seeks to follow the RFC as close
as possible, with the only deliberate deviation being the addition of
support for all the HMAC algorithms already supported by Bird, as well as
the Blake2b variant of the Blake algorithm.
For description of applicability, assumptions and security properties,
see RFC 8967 sections 1.1 and 1.2.
|
|
In preparation for adding authentication checks, refactor the TLV
walking code so it can be reused for a separate pass of the packet
for authentication checks.
|
|
Routes from downed protocols stay in rtable (until next rtable prune
cycle ends) and may be even exported to another protocol. In BGP case,
source BGP protocol is examined, although dynamic parts (including
neighbor entries) are already freed. That may lead to crash under some
race conditions. Ensure that freed neighbor entry is not accessed to
avoid this issue.
|
|
underlying interface disappears
When an interface disappears, all the neighbors are freed as well. Seqno
requests were anyway not decoupled from them, leading to strange
segfaults. This fix adds a proper seqno request list inside neighbors to
make sure that no pointer to neighbor is kept after free.
|
|
Some area handling code got confused by IPv4 setup in OSPFv3 mode.
|
|
The babel protocol code checks whether iface supports multicast, and
whether it has a link-local address assigned. However, it doesn not give
any feedback if any of those checks fail, it just silently ignores the
interface. Fix this by explicitly logging when multicast check fails.
Based on patch from Toke Høiland-Jørgensen, thanks!
|
|
Ifaces with host address (/32) were forced to be stubby, but now they
can be used as PtP or PtMP. For these ifaces we need to:
- Do not force stub mode
- Accept packets from any IP as local
- Accept any configured neighbor as local
- Detect ifaces properly as unnumbered
- Use ONLINK flag for nexthops
|
|
As specified in RFC 2328 8.1: "On physical point-to-point networks,
the IP destination is always set to the address AllSPFRouters."
Note that this likely break setups with multiple neighbors on a network
configured as PtP, which worked before. These should be configured as
PtMP.
Thanks to Senthil Kumar Nagappan for the original patch and to Joakim
Tjernlund for suggestions.
|
|
Common behavior for LSupd and delayed LSack moved to ospf_send_to_iface()
and other minor changes.
|
|
|
|
The flag makes sense just in external representation. It is reset during
BGP export, but keeping it internally broke MRT dumps for short attributes
that used it anyways.
Thanks to Simon Marsh for the bugreport and the patch.
|
|
BGP statistics code was preliminary and i wanted to replace it by
separate 'show X stats' command. The patch hides the preliminary
output in 'show protocols all' so it is not part of the released
version.
|
|
|
|
|
|
Pipe channels are kind-of implicit, so setting protocol debug flags
should also set pipe debug flags.
|
|
In OSPFv3, only Hello and DBDes packets contain flags specifying whether
RFC 7166 authentication trailer is used. Other packets are processed
based on stored authentication state in neighbor structure. Update this
state with each received Hello to handle authentication change from
reconfigurations.
Thanks to Joakim Tjernlund and Kenth Eriksson for the bugreport.
|
|
|
|
Also, no automatic reload for BGP channels without import/export table.
|
|
This is an implementation of draft-walton-bgp-hostname-capability-02.
It is implemented since quite some time for FRR and in datacenter, this
gives a nice output to avoid using IP addresses.
It is disabled by default. The hostname is retrieved from uname(2) and
can be overriden with "hostname" option. The domain name is never set
nor displayed.
Minor changes by committer.
|
|
Flag signalling that MP-BGP mode should be used got reset after first
batch of routes, so remaining routes were processed without that, leading
to missing MP_REACH_NLRI attribute.
Thanks to Piotr Wydrych for the bugreport.
|
|
Add fake MP_REACH_NLRI attribute with BGP next hop when encoding MRT
table dumps for IPv6 routes. That is necessary to encode next hop as
NEXT_HOP attribute is not used for MP-BGP.
Thanks to Santiago Aggio for the bugreport.
|
|
Direct BFD sessions needs to be dispatched not only by IP addresses, but
also by interfaces, in order to avoid collisions between neighbors with
the same IPv6 link-local addresses.
Extend BFD session hash_ip key by interface index to handle that. Use 0
for multihop sessions.
Thanks to Sebastian Hahn for the original patch.
|
|
It was mixed-up if hostname is IPv6 address, and reporting separate
values (like port) on separate lines fits better into key-value style
of 'show protocols all' output. Also, the patch simplifies transport
identification formatting (although it is unused now).
Thanks to Alarig Le Lay for the suggestion.
|
|
The option is not implemented since transition to 2.0 and no plan to add it.
Also remove some deprecated RTS_* valus from documentation.
Thanks to Sébastien Parisot for notification.
|
|
We need to define 'net' field temporarily as it may be accessed by
per-route filters.
Thanks to Damian Zaremba for the bugreport.
|
|
The patch add support for per-channel debug flags, currently just
'states', 'routes', and 'filters'. Flag 'states' is used for channel
state changes, remaining two for routes passed through the channel.
The per-protocol debug flags 'routes'/'filters' still enable reporting
of routes for all channels, to keep existing behavior.
The patch causes minor changes in some log messages.
|
|
This fixes an issue with dirty node passed to add_tail().
Thanks to Andreas Rammhold for the initial patch.
|
|
When config structures are copied due to template application,
we need to reset list node structure before calling add_tail().
Thanks to Mikael Magnusson for patches.
|
|
|
|
The babel protocol code was initialising objects returned from the slab
allocator by assigning to each of the struct members individually, but
wasn't touching the NODE member while doing so. This leads to warnings on
debug builds since commit:
baac7009063d ("List expensive check.")
To fix this, introduce an sl_allocz() variant of the slab allocator which
will zero out the memory before returning it, and switch all the babel call
sites to use this version. The overhead for doing this should be negligible
for small objects, and in the case of babel, the largest object being
allocated was being zeroed anyway, so we can drop the memset in
babel_read_tlv().
|
|
Add support for proper handling of multiple routes with the same network
to the static protocol. Routes are distinguished by internal index, which
is assigned automatically (sequentially for routes within each network).
Having different route preference or igp_metric attribute is optional.
|
|
When a new link-LSA is originated, we need to notify intra-area-prefix-LSA
handling, like when a new link-LSA is received. Otherwise a new network
prefix added to a DR is not propagated immediately.
Thanks to Bala Sajja for the bugreport.
|
|
Merge multiple BFD option blocks in BGP configs instead of using the last
one. That is necessary for proper handling of templates when BFD options
are used both in a BGP template and in a BGP protocol derived from that
template.
|
|
|
|
BFD session options are configured per interface in BFD protocol. This
patch allows to specify them also per-request in protocols requesting
sessions (currently limited to BGP).
|
|
Add 'ignore max length' option to RPKI protocol, which ignores received
max length in ROA records and instead uses max value (32 or 128). This
may be useful for implementing loose RPKI check for blackholes.
|
|
|
|
Sometimes multicast OSPF packet is received when neighbor adjacency is
not established. Such packet should be ignored earlier in packet
processing as otherwise it causes strange error messages when OSPFv3
authentication is enabled.
|
|
Most commands like 'show ospf neighbors' fail when protocol is not
specified and there are multiple instances of given protocol type.
This is annoying in BIRD 2, as many protocols have IPv4 and IPv6
instances. The patch changes that by showing output from all protocol
instances of appropriate type.
Note that the patch also removes terminating cli_msg() call from these
commands and moves it to the common iterating code.
|
|
Thanks to Slava Aseev for the thorough bugreport.
|
|
Compare the new timing parameters with the old configuration, not with
the temporary state of the current connection.
The timing values in struct rpki_cache is updated by a version 1 End Of
Data PDU, unless this behavior is suppressed by the configuration
explicitly by the "keep" keyword. Consequently, every reconfiguration
of BIRD triggers a reconnection even if it is not necessary.
|
|
|
|
If the next hop of a route is not a reachable address, the route should be
installed as onlink. This enables a configuration common in mesh networks
where the mesh interface is assigned a /32 and babel handles the routing by
installing onlink routes.
Thanks to Toke Hoiland-Jorgensen for the patch.
|
