| Age | Commit message (Collapse) | Author |
|---|
|
|
|
This commit removes the EAF_TYPE_* namespace completely and also for
route attributes, filter-based types T_* are used. This simplifies
fetching and setting route attributes from filters.
Also, there is now union bval which serves as an universal value holder
instead of private unions held separately by eattr and filter code.
|
|
|
|
|
|
Before this change, fetch-update-write and bitmasking was hardcoded in
attribute access code cased by the attribute type. Several filter
instructions are used to do it instead.
As this is certainly going to be a little bit slower than before, the
switch block in attribute access code should be completely removed in
near future, helping with both performance and code cleanliness.
The user interface should have stayed intact.
|
|
|
|
The interface pointer was improperly converted to u32 and back. Fixing
this by explicitly allocating an adata structure for it. It's not so
memory efficient, we'll optimize this later.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
compatibility
|
|
|
|
Conflicts:
proto/bgp/attrs.c
proto/pipe/pipe.c
|
|
|
|
|
|
|
|
|
|
|
|
The prune loop may may rebuild the prefix trie and therefore invalidate
walk state for asynchronous walks (used in 'show route in' cmd). Fix it
by adding locking that keeps the old trie in memory until current walks
are done.
In future this could be improved by rebuilding trie walk states (by
lookup for last found prefix) after the prefix trie rebuild.
|
|
When rtable is pruned and network fib nodes are removed, we also need to
prune prefix trie. Unfortunately, rebuilding prefix trie takes long time
(got about 400 ms for 1M networks), so must not be atomic, we have to
rebuild a new trie while current one is still active. That may require
some considerable amount of temporary memory, so we do that only if
we expect significant trie size reduction.
|
|
Implement flowspec validation procedure as described in RFC 8955 sec. 6
and RFC 9117. The Validation procedure enforces that only routers in the
forwarding path for a network can originate flowspec rules for that
network.
The patch adds new mechanism for tracking inter-table dependencies, which
is necessary as the flowspec validation depends on IP routes, and flowspec
rules must be revalidated when best IP routes change.
The validation procedure is disabled by default and requires that
relevant IP table uses trie, as it uses interval queries for subnets.
|
|
Allow to specify sorted flag, trie fla, and min/max settle time.
Also do not enable trie by default, it must be explicitly enabled.
|
|
|
|
When output of 'show route' command was generated, the net_format() was
called for each network prematurely, even if the result was not needed.
Fix the code to call net_format() only when needed. This makes queries
that process many networks but show only few (e.g. 'show route where ..',
or 'show route count') much faster (like 5x - 10x faster).
|
|
Add trie iteration code to rt_show_cont() CLI hook and use it to
accelerate 'show route in <addr>' commands using interval queries.
|
|
Implement 'show route in <addr>' command, which shows all routes in
networks that are subnets of given network. Currently limited to IP
network types.
|
|
Attach a prefix trie to IP/VPN/ROA tables. Use it for net_route() and
net_roa_check(). This leads to 3-5x speedups for IPv4 and 5-10x
speedup for IPv6 of these calls.
TODO:
- Rebuild the trie during rt_prune_table()
- Better way to avoid trie_add_prefix() in net_get() for existing tables
- Make it configurable (?)
|
|
Add operators .min and .max to find minumum or maximum element in sets
of types: clist, eclist, lclist. Example usage:
bgp_community.min
bgp_ext_community.max
filter(bgp_large_community, [(as1, as2, *)]).min
Signed-off-by: Alexander Zubkov <green@qrator.net>
|
|
Compare all IA_* flags that are set by sysdep iface code.
The old code ignores IA_SECONDARY flag when comparing whether iface
address updates from kernel changed anything. This is usually not an
issue as kernel removes all secondary addresses due to removal of the
primary one, but it breaks when sysctl 'promote_secondaries' is enabled
and kernel promotes secondary addresses to primary ones.
Thanks to 'Alexander' for the bugreport.
|
|
This feature is intended mostly for checking that BIRD's allocation
strategies don't consume much memory space. There are some cases where
withdrawing routes in a specific order lead to memory fragmentation and
this output should give the user at least a notion of how much memory is
actually used for data storage and how much memory is "just allocated"
or used for overhead.
Also raising the "system allocator overhead estimation" from 8 to 16
bytes; it is probably even more. I've found 16 as a local minimum in
best scenarios among reachable machines. I couldn't find any reasonable
method to estimate this value when BIRD starts up.
This commit also fixes the inaccurate computation of memory overhead for
slabs where the "system allocater overhead estimation" was improperly
added to the size of mmap-ed memory.
|
|
|
|
|
|
|
|
|
|
pflags
|
|
It is an auxiliary key in the routing table, not a route attribute.
|
|
|
|
|
|
Kernel route sync is done by other ways now and this code is not used
currently.
|
|
|
|
This is needed to provide the protocols the full old route after filters
when export table is enabled.
|
|
|
|
|
|
|
|
|
