| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Add basic VRF (virtual routing and forwarding) support. Protocols can be
associated with VRFs, such protocols will be restricted to interfaces
assigned to the VRF (as reported by Linux kernel) and will use sockets
bound to the VRF. E.g., different multihop BGP instances can use diffent
kernel routing tables to handle BGP TCP connections.
The VRF support is preliminary, currently there are several limitations:
- Recent Linux kernels (4.11) do not handle correctly sockets bound
to interaces that are part of VRF, so most protocols other than multihop
BGP do not work. This will be fixed by future kernel versions.
- Neighbor cache ignores VRFs. Breaks config with the same prefix on
local interfaces in different VRFs. Not much problem as single hop
protocols do not work anyways.
- Olock code ignores VRFs. Breaks config with multiple BGP peers with the
same IP address in different VRFs.
- Incoming BGP connections are not dispatched according to VRFs.
Breaks config with multiple BGP peers with the same IP address in
different VRFs. Perhaps we would need some kernel API to read VRF of
incoming connection? Or probably use multiple listening sockets in
int-new branch.
- We should handle master VRF interface up/down events and perhaps
disable associated protocols when VRF goes down. Or at least disable
associated interfaces.
- Also we should check if the master iface is really VRF iface and
not some other kind of master iface.
- BFD session request dispatch should be aware of VRFs.
- Perhaps kernel protocol should read default kernel table ID from VRF
iface so it is not necessary to configure it.
- Perhaps we should have per-VRF default table.
|
|
|
|
|
|
The RPKI protocol (RFC 6810) using the RTRLib
(http://rpki.realmv6.org/) that is integrated inside
the BIRD's code.
Implemeted transports are:
- unprotected transport over TCP
- secure transport over SSHv2
Example configuration of bird.conf:
...
roa4 table r4;
roa6 table r6;
protocol rpki {
debug all;
# Import both IPv4 and IPv6 ROAs
roa4 { table r4; };
roa6 { table r6; };
# Set cache server (validator) address,
# overwrite default port 323
remote "rpki-validator.realmv6.org" port 8282;
# Overwrite default time intervals
retry 10; # Default 600 seconds
refresh 60; # Default 3600 seconds
expire 600; # Default 7200 seconds
}
protocol rpki {
debug all;
# Import only IPv4 routes
roa4 { table r4; };
# Set cache server address to localhost,
# use default ports tcp => 323 or ssh => 22
remote 127.0.0.1;
# Use SSH transport instead of unprotected transport over TCP
ssh encryption {
bird private key "/home/birdgeek/.ssh/id_rsa";
remote public key "/home/birdgeek/.ssh/known_hosts";
user "birdgeek";
};
}
...
|
|
|
|
There are several unresolved -Wmissing-field-initializers on older
versions of GCC than 5.1, all of them false positive.
|
|
AF can be specified implicitly by saddr or daddr, flags SKF_V4ONLY and
SKF_V6ONLY are to be removed.
|
|
|
|
Add code for manipulation with TCP-MD5 keys in the IPsec SA/SP database
at FreeBSD systems. Now, BGP MD5 authentication (RFC 2385) keys are
handled automatically on both Linux and FreeBSD.
Based on patches from Pavel Tvrdik.
|
|
|
|
In BIRD, RX has lower priority than TX with the exception of RX from
control socket. The patch replaces heuristic based on socket type with
explicit mark and uses it for both control socket and BGP session waiting
to be established.
This should avoid an issue when during heavy load, outgoing connection
could connect (TX event), send open, but then failed to receive OPEN /
establish in time, not sending notifications between and therefore
got hold timer expired error from the neighbor immediately after it
finally established the connection.
|
|
|
|
Moved the code to sysdep.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
I/O:
- BSD: specify src addr on IP sockets by IP_HDRINCL
- BSD: specify src addr on UDP sockets by IP_SENDSRCADDR
- Linux: specify src addr on IP/UDP sockets by IP_PKTINFO
- IPv6: specify src addr on IP/UDP sockets by IPV6_PKTINFO
- Alternative SKF_BIND flag for binding to IP address
- Allows IP/UDP sockets without tx_hook, on these
sockets a packet is discarded when TX queue is full
- Use consistently SOL_ for socket layer values.
OSPF:
- Packet src addr is always explicitly set
- Support for secondary addresses in BSD
- Dynamic RX/TX buffers
- Fixes some minor buffer overruns
- Interface option 'tx length'
- Names for vlink pseudoifaces (vlinkX)
- Vlinks use separate socket for TX
- Vlinks do not use fixed associated iface
- Fixes TTL for direct unicast packets
- Fixes DONTROUTE for OSPF sockets
- Use ifa->ifname instead of ifa->iface->name
|
|
|
|
Interfaces for OSPF and RIP could be configured to use (and request)
TTL 255 for traffic to direct neighbors.
Thanks to Simon Dickhoven for the original patch for RIPng.
|
|
Implements support for IPv6 traffic class, sets higher priority for OSPF
and RIP outgoing packets by default and allows to configure ToS/DS/TClass
IP header field and the local priority of outgoing packets.
|
|
|
|
|
|
Thanks to Alexander V. Chernikov for the patch.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
There is no reak callback scheduler and previous behavior causes
bad things during hard congestion (like BGP hold timeouts).
Smart callback scheduler is still missing, but main loop was
changed such that it first processes all tx callbacks (which
are fast enough) (but max 4* per socket) + rx callbacks for CLI,
and in the second phase it processes one rx callback per
socket up to four sockets (as rx callback can be slow when
there are too many protocols, because route redistribution
is done synchronously inside rx callback). If there is event
callback ready, second phase is skipped in 90% of iterations
(to speed up CLI during congestion).
|
|
|
|
|
|
ttl 1.
|
|
|
|
|
|
you can delete the socket from anywhere in the hooks and nothing should break.
Also, the receive/transmit buffers are now regular xmalloc()'ed buffers,
not separate resources which would need shuffling around between pools.
sk_close() is gone, use rfree() instead.
|
|
socket hook. Replaces the SK_DELETED hack.
Squashed a couple of bugs in handling of TCP sockets.
|
|
|
|
|
|
See comments in lib/socket.h for a detailed guide on how to use them.
|
|
especially for netlink communication.
|
|
|
|
|
|
gcc -MM can be used to separate them from the system ones.
Added automatic generation of dependencies.
|
