| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Also fix several minor bugs and add 'limit' option for k-out-of-j
link sensing strategy. Change default from 8-of-16 to 12-of-16.
Change IHU expiry factor from 1.5 to 3.5 (as in RFC 6126).
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Note that recurrent timers are currently limited to ~1 hour.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Use '%t' in bsnprintf() for microsecond times (in btime) with variable
sub-second precision.
|
|
Date/time output (e.g. in logs, show commands) can use %f to specify
subsecond time. By default, millisecond precision is used in output.
|
|
The old timer interface is still kept, but implemented by new timers. The
plan is to switch from the old inteface to the new interface, then clean
it up.
|
|
|
|
|
|
|
|
|
|
Also redesign preferred address selection and update protocols to use
appropriate preferred address.
Based on a previous work by Jan Maria Matejka.
|
|
|
|
|
|
|
|
The TTL check must be done after instance ID dispatch to avoid warnings
when a physical iface is shared by multiple instances and some use TTL
security and some not.
|
|
In such case, next hop has to be taken from Link-LSA like in broadcast
case, not from neighbor source address like in other PtP cases.
Also add some checks, comments and code cleanup.
|
|
OSPFv3-AF can handle multiple topologies of diferent address families
(IPv4, IPv6, both unicast and multicast) using separate instances
distinguished by instance ID ranges.
|
|
Make it syntactically correct, so it is accepted.
|
|
|
|
|
|
Adapt the naming conventions to be a bit closer to the other protocols.
proto_radv -> radv_proto
struct radv_proto *ra -> struct radv_proto *p
struct proto *p -> struct proto *P
|
|
Adapt the naming conventions to be a bit closer to the other protocols.
proto_radv -> radv_proto
struct radv_proto *ra -> struct radv_proto *p
struct proto *p -> struct proto *P
|
|
|
|
|
|
|
|
Add proper support for per-nexthop onlink flag in routes to handle next
hop addresses that are not covered by interface IP ranges. Supported by
kernel and static protocols.
Thanks to Vincent Bernat for the idea.
|
|
Thanks to Lennert Buytenhek <buytenh@wantstofly.org> for the patch.
|
|
The subtlv parsing code was doing byte-based arithmetic with non-void pointers,
causing it to read beyond the end of the packet.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
|
|
RFC6126bis formally introduces sub-TLVs to the Babel protocol, including
mandatory sub-TLVs. This adds support for parsing sub-TLVs to the Babel
protocol and skips TLVs that contain mandatory sub-TLVs, as per the spec.
For details, see section 4.4 of
https://tools.ietf.org/html/draft-ietf-babel-rfc6126bis-02
Thanks to Toke Høiland-Jørgensen <toke@toke.dk> for the patch.
|
|
Previously, the Babel protocol would never use prefix compression on outgoing
updates (but would parse it on incoming ones). This adds compression of IPv6
addresses of outgoing updates.
The compression only works to the extent that the FIB is walked in lexicographic
order; i.e. a prefix is only compressed if it shares bytes with the previous
prefix in the same packet.
Thanks to Toke Høiland-Jørgensen <toke@toke.dk> for the patch.
|
|
This updates the documentation for the Babel protocol to mention the fact
that it now supports dual-stack operation, and adds documentation for the
new next hop options.
Thanks to Toke Høiland-Jørgensen <toke@toke.dk> for the patch.
|
|
This adds support for dual-stack v4/v6 operation to the Babel protocol.
Routing messages will be exchanged over IPv6, but IPv4 routes can be
carried in the messages being exchanged. This matches how the reference
Babel implementation (babeld) works.
The nexthop address for v4 can be configured per interface, and will
default to the first available IPv4 address on the given interface. For
symmetry, a configuration option to configure the IPv6 nexthop address
is also added.
Thanks to Toke Høiland-Jørgensen <toke@toke.dk> for the patch.
|
|
|
|
|
|
|
|
|
