| Age | Commit message (Collapse) | Author |
|---|
|
Sometimes multicast OSPF packet is received when neighbor adjacency is
not established. Such packet should be ignored earlier in packet
processing as otherwise it causes strange error messages when OSPFv3
authentication is enabled.
|
|
Put new non-best routes to the end of list instead of the second
position. Put updated routes to their old position. Position is changed
just by best route selection.
|
|
Most commands like 'show ospf neighbors' fail when protocol is not
specified and there are multiple instances of given protocol type.
This is annoying in BIRD 2, as many protocols have IPv4 and IPv6
instances. The patch changes that by showing output from all protocol
instances of appropriate type.
Note that the patch also removes terminating cli_msg() call from these
commands and moves it to the common iterating code.
|
|
Compare the content of PM_ASN_SET in path masks. A reconfiguration
was not properly triggering a reload of affected protocols when the
members of a set in a path mask change.
Also, update the printing code to so that it can display sets in a path
mask.
|
|
Add a missing return statement. Path masks with the same length were all
considered the same. Comparing two with different length would cause
out-of-bounds memory access.
|
|
Thanks to Slava Aseev for the thorough bugreport.
|
|
|
|
|
|
Add support for RTA_MULTIPATH attribute parsing for AF_MPLS routes.
BIRD is capable of installing a multipath route into kernel on Linux,
but it would not be seen because parsing fails. This made BIRD attempt
to install the same route repeatedly.
(The patch minorly updated by committer)
|
|
Compare the new timing parameters with the old configuration, not with
the temporary state of the current connection.
The timing values in struct rpki_cache is updated by a version 1 End Of
Data PDU, unless this behavior is suppressed by the configuration
explicitly by the "keep" keyword. Consequently, every reconfiguration
of BIRD triggers a reconnection even if it is not necessary.
|
|
This is a quick workaround for an issue where configured logfiles are
opened/created during parsing of a config file even when parse-and-exit
option is active. We should later refactor the logging code to avoid
opening log during parsing altogether.
|
|
|
|
If the next hop of a route is not a reachable address, the route should be
installed as onlink. This enables a configuration common in mesh networks
where the mesh interface is assigned a /32 and babel handles the routing by
installing onlink routes.
Thanks to Toke Hoiland-Jorgensen for the patch.
|
|
This issue has a long history. In 2012, we changed data field for
unnumbered PtP links from iface id (specified by RFC) to IP address based
on reports of bugs in Quagga that required it, and we used out-of-band
information to distinquish unnumberred PtPs with the same local IP
address.
Then with OSPF graceful restart implementation, we found that we can no
longer use out-of-band information, and we need to use only LSAdb info
for routing table calculation, but i forgot to finish handling of this
case, so multiple unnumbered PtPs with the same local IP addresses were
broken.
Considering that even recent Mikrotik RouterOS has broken next hop
calculation that depends on IP address in PtP link data field, we
cannot just switch back to the iface id for unnumbered PtP links.
The patch makes two changes: First, it goes back to use out-of-band
(position) info for distinguishing local interfaces in SPF when graceful
restart is not enabled, while still uses LSAdb-only approach for SPF
calculation when graceful restart is enabled.
Second, it adds OSPF interface option 'ptp address', which controls
whether IP address or iface id is used in data field. It is enabled
by default except for unnumbered PtP links with enabled graceful
restart.
Thanks to Kenth Eriksson for the bugreport and Joakim Tjernlund for
suggestions.
|
|
There is nothing in RFCs specifying that id 0 is not allowed. Some
implementations does not support it, while some other use key id 0 by
default. We allow it but start with key id 1 by default.
Thanks to Kenth Eriksson for the bugreport.
|
|
|
|
Implement regex-like '+' operator in BGP path masks to match previous
path mask item multiple times. This is useful as ASNs may appear
multiple times in paths due to path prepending for traffic engineering
purposes.
|
|
|
|
Resolve neighbors using longest prefix match. Although interface ranges
should not generally collide, it may happen for unnumbered links.
Thanks to Kenth Eriksson for the bugreport.
|
|
|
|
|
|
No need for this debug filter command and it can be abused from CLI.
|
|
|
|
|
|
|
|
|
|
|
|
This is not needed as the string is always short enough, anyway
it may be needed in future and one strlen during BIRD start is
cheap enough.
|
|
that function.
|
|
|
|
|
|
change anything
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
NULL pointer is safer than a random pointer onto stack if this function
gets changed and eventually broken.
|
|
|
|
Intended to be run at every operation with complex data structures
to check their consistency and validity.
|
|
|
|
|
|
|
|
|
|
There are three common ways how to encode IPv6 link-local-only next hops:
(:: ll), (ll), and (ll ll). We use the first one but we should accept all
three. The patch fixes handling of the last one.
Thanks to Sebastian Hahn for the bugreport.
|
|
|
|
|
|
|
